User manual SAGEM CDP 1100-X

DON'T FORGET : ALWAYS READ THE USER GUIDE BEFORE BUYING !!!

If this document matches the user guide, instructions manual or user manual, feature sets, schematics you are looking for, download it now. Diplodocs provides you a fast and easy access to the user manual SAGEM CDP 1100-X. We hope that this SAGEM CDP 1100-X user guide will be useful to you.


SAGEM CDP 1100-X : Download the complete user guide (1146 Ko)

You may also download the following manuals related to this product:

   SAGEM CDP 1100-X (1154 ko)
   SAGEM CDP 1100-X (1588 ko)
   SAGEM CDP 1100-X (1154 ko)
   SAGEM CDP 1100-X (1588 ko)
   SAGEM CDP 1100-X DATASHEET (103 ko)
   SAGEM CDP 1100-X DATASHEET (822 ko)
   SAGEM CDP 1100-X DATASHEET (817 ko)

Manual abstract: user guide SAGEM CDP 1100-X

Detailed instructions for use are in the User's Guide.

[. . . ] Table of Contents Table of Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Usage Notice . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 English Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] 4. Power Cord VGA Cable S-Video Cable Composite Video Cable v To ensure the projector works well with your computer, please set the display mode of your graphic card than or equal to 1024 X 768 resolution. Make sure timing of the display mode is compatible with the projector. Refer to the Compatibility Modes section on page 30. 9 English Installation Powering On/Off the Projector Powering On the Projector 1. The startup screen will display for 20 seconds and the Power/Standby indicator will flash green. When the startup screen disappears, the Power/Standby indicator will turn green. v If the screen displays No Signal, please make sure the signal cables are securely connected. v If you connect multiple sources at the same time, use the Source button on the remote control or control panel to switch. 2 Power vTurn on the projector first and then the computer. 1 Lens cap 10 Installation Powering Off the Projector 1. After pressing the Power button, you will see a message Power off the lamp?If you want to turn on the projector again, you must press the Power button within 40 seconds of the flashing indicator. Disconnect the power cord from the electrical outlet and the projector. Do not turn on the projector immediately following a power off procedure. English Warning Indicator v When the Warning indicator turns red, it indicates the projector has overheated. v When the Warning indicator flashes red (0. 5 second intervals), it indicates a problem with the lamp. Turn off the projector and disconnect the power cord from the electrical outlet, then contact your local dealer or our service center. v When the Warning indicator flashes red (1 second intervals), it indicates an internal problem. Stop using the projector and disconnect the power cord from the electrical outlet, then contact your local dealer or our service center. v When the Warning indicator flashes orange, it indicates highspeed cooling in progress. This is not an abnormal condition, and you can continue using the projector. 11 English Installation Adjusting the Projected Image Adjusting the Projector Height The projector is equipped with an elevator foot for adjusting the projector height. To raise the projector: 1. Raise the projector to the desired display angle , then release the button to lock the elevator foot into position. Lower the projector, then release the button to lock the elevator foot into position. Use to fine-tune the display angle. 1 3 2 Elevator Button Tilt Adjusted wheel Elevator Foot 12 Installation Adjusting the Projector Zoom / Focus You may adjust zoom ring to zoom in or out. The projector will focus at distances from 3. 94 to 32. 81 feet (1. 20 to 10. 0 meters). English Focus Ring Zoom Ring Adjusting Projection Image Size 267. 2"(678. 7cm) 213. 8"(543. 0cm) 160. 3" (407. 2cm) 229. 8" (583. 7cm) 183. 8" (466. 9cm) 133. 6"(339. 3cm) 137. 9" (350. 2cm) 80. 2"(203. 6cm) 114. 9" (291. 8cm) 32. 1"(81. 4cm) 68. 9" (175. 1cm) 27. 6" (70. 0cm) 3. 94' (1. 2m) 9. 84' (3. 0m) 16. 40' (5. 0m) 19. 69' (6. 0m) 26. 25' (8. 0m) 32. 81' (10. 0m) Screen (Diagonal) Screen Size Max. To open the OSD menu, press Menu on the Remote Control or Panel Control. 2. [. . . ] Verify that the resolution setting is less than or equal to 1024 x 768 resolution. If the projector is still not projecting the whole image, you will also need to change the monitor display you are using. Then select Standard monitor types under the Manufactures box ; choose the resolution mode you need under the Models box. Verify that the resolution setting of the monitor display is less than or equal to 1024 x 768. 4 If you are using a Notebook PC: 1. [. . . ]

DISCLAIMER TO DOWNLOAD THE USER GUIDE SAGEM CDP 1100-X




Click on "Download the user Manual" at the end of this Contract if you accept its terms, the downloading of the manual SAGEM CDP 1100-X will begin.

 

Copyright © 2015 - manualRetreiver - All Rights Reserved.
Designated trademarks and brands are the property of their respective owners.