User manual SAGEM F@ST 9089 ETHERNET

[. . . ] SAGEM F@stTM 908/948 Ethernet/USB Combo ADSL Modem Reference Manual - Ethernet Interface Reference: 288 055 899 ed. 1 July 2004 Issue S SAGEM F@st TM 908 / 948 Reference Manual - Ethernet Interface E closely follows all technical changes and continually strives to improve its products for the benefit of its customers. It therefore reserves the right to change its documentation accordingly without notice. All the trademarks mentioned in this manual are registered by their respective owners: SAGEM F@stTM is a registered trademark of E, · · WindowsTM and Internet ExplorerTM are registered trademarks of Microsoft Corporation, Apple and MacOS are registered trademarks of Apple Computer Incorporation. [. . . ] In this case, you have to parameter it to make your modem operational. To allow traffic, enter the following characteristics : - External Port number : 3456, - Internal Port number : 3456, - Transport layer Protocol : UDP. To set the firewall activated: 1) Firewall provided with Windows XP, refer to chapter 6 (appendice), 2) Software external to your computer, refer to appropriate documentation. 15 SAGEM F@st TM 908 / 948 Reference Manual - Ethernet Interface 2. 5. 2 Button Apply Restart Active buttons Meaning Registers the changes to the "Bridge Lock" mode. Updates the modem's onboard software from the BridgeMon application (see section below). Closes the BridgeMon diagnostics screen, but keeps the BridgeMon application running. SW Upgrade About Close 16 SAGEM F@st TM 908 / 948 Reference Manual - Ethernet Interface 2. 5. 3 Updating the modem software from the BridgeMon application The SAGEM F@stTM 908/948 contains a permanent memory for saving the onboard software. Click the SW Upgrade button in the "BridgeMon" screen and the screen opposite appears. On Microsoft Windows XP, you can use the Windows XP PPPoE client instead. On MacOS MacOS 8. 6 et 9 : The PPPoE client software utility is provided on the CD-ROM. The PPPoE client software utility is integrated in the operating system. Please refer to sections 3. 1. 3 and 3. 1. 4 for the configuration. MacOS X : 18 SAGEM F@st TM 908 / 948 Reference Manual - Ethernet Interface 3. 1. 1 Configuring the PPPoE client in Windows XP You can skip this paragraph if you did the installation according to § 2. 1 ! 1 The installation procedure described below does not apply to any Microsoft operating systems other than Windows XP. In the Start menu, select Control panel, Network and Internet connections; the screen opposite appears. Click "Create a new connection" in the "Network tasks" area, or select File / New connection in the menu bar. 19 SAGEM F@st 3 TM 908 / 948 Reference Manual - Ethernet Interface When the following screen appears, select "Connect to the Internet". up my connection Then click Next. 5 The following screen appears. Select "Connect using a broadband connection that requires a user name and password ". Then click Next. 6 The next screen lets you name your connection. Then click Next. 20 SAGEM F@st 7 TM 908 / 948 Reference Manual - Ethernet Interface The next screen lets you store the information on your Internet account. Enter your "User name", Enter your "Password" and confirm. Check the box if you want to create an Internet ADSL shortcut on your desktop. Finally, click Finish. At this point, your Internet connection is created. You can now log on to the Internet. 21 SAGEM F@st TM 908 / 948 Reference Manual - Ethernet Interface 3. 1. 2 1 Internet reconnection in Windows XP If you checked the appropriate icon box, the will have been created on the desktop. Double click this icon and the screen opposite appears. 2 3 Then click on "Connexion". The screen opposite appears : Enter your user name and password Then click OK. 4 Open your browser. You can now surf the Internet. 22 SAGEM F@st TM 908 / 948 Reference Manual - Ethernet Interface 3. 1. 3 1 Configuring the PPPoE client in MacOS X (apple) menu in the Click the menu bar, select System Preferences, then click the Network icon. [. . . ] It does not use the power supply provided by the USB interface. 5. 2. 2 Modem not detected Firstly check that the conditions in the previous section are satisfied. LEDs Flag Status Corrective action Check that the Ethernet cable supplied in your pack is correctly connected to your modem, and to an active Ethernet port on your computer. The Ethernet cable to be used is a cross-pinned UTP RJ45 cable. Modem powered. ADSL off PWR off Red Modem not detected by your computer. 31 SAGEM F@st TM 908 / 948 Reference Manual - Ethernet Interface 5. 2. 3 Absence of ADSL synchronization Firstly check that the conditions in the previous section are satisfied. [. . . ]