User manual SAGEM MYX2-2

[. . . ] mars 2005 11:48 11 ENGLISH S 251959374_myX2-2_lu_en. book Page 2 Mercredi, 30. mars 2005 11:48 11 You have just purchased a SAGEM mobile phone, and we congratulate you on your choice. Your phone can be used internationally in the various dual band networks (GSM 900 MHz and DCS 1800 MHz) depending on the roaming arrangements with your operator. This user guide presents the SAGEM myX2-2 and myX2-2m mobile phones range. [. . . ] Advanced. . . : offers the following advanced settings - Configuring parameters - Show URL - Logoff - Circuit message (if user can confirm each logon) - Security (is used to access information on making WAP connections secure). The WAP navigator is under licence: 32 WAP 251959374_myX2-2_lu_en. book Page 33 Mercredi, 30. mars 2005 11:48 11 Configuring WAP parameters Select the Advanced. . . Choose from the sub-menus offered: Logon parameters is used to select or modify your access provider's logon parameters or configure the parameters of other access providers. Configuration of GSM and GPRS parameters (depending on model): All information to be entered in the parameters are provided by your operator or access provider. - Enter parameters of preferred logon: · GPRS otherwise GSM (by default): the logon to WAP services uses the GPRS as a priority. However, in the event of unavailability of the GPRS network, the GSM network is used to establish the link. · GPRS: the logon to WAP services uses the GPRS network exclusively. · GSM: the logon to WAP services uses the GSM network exclusively. The GSM parameters to be entered are: - User name - Password - IP address of WAP gateway - Port type (secure or insecure) - Call number - Access mode (digital, analogue or automatic) In automatic mode access can be gained to the operator's network by a digital link and by an analogue link to a different network (in roaming). The GPRS parameters to be entered are: - User name - Password - IP address of WAP gateway - Port type (secure or insecure) [Choice] then the APN menu. - APN: if no APN has been defined, press the right programmable key Select or add and APN. WAP 33 251959374_myX2-2_lu_en. book Page 34 Mercredi, 30. mars 2005 11:48 11 Once all the settings have been entered, you can activate the chosen access provider. Inactivity time is used to choose the time after which the call is automatically disconnected if you have forgotten to log off from a service. WAP Logging on The connection to a WAP service on the GPRS network is not cut if an incoming call is received. Using the Welcome menu, you can log onto your access provider's WAP site by pressing the right programmable key . If you are logging onto the GSM network, the @ symbol flashes, the metering of the cost of the call starts as soon as it stops flashing. Downloading objects Some WAP sites allow you to download ring tones, icons or animated screensavers. You can then save them in your phone (same operation as used for downloading using SMS). WAP Logging off To log off press Stop key. The logoff happens automatically after a few seconds of inactivity if you forget to log off. This period is defined by the inactivity time setting. GPRS (depending on model) A flashing icon indicates that the phone is logging onto a GPRS network. A non-flashing icon indicates that the GPRS network is available; if the icon is dark, it indicates that the phone is logged onto the GPRS network: see page 41 for the attachment options. This icon is not displayed if the GPRS network is not available or if the SIM card inserted in your phone does not include the GPRS service. It may also disappear when accessing WAP services if the connection uses the GSM network instead of the GPRS network. 34 WAP 251959374_myX2-2_lu_en. book Page 35 Mercredi, 30. [. . . ] Impossible to send message Check that the SIM card used offers this service. To do so, please select go to the Messages menu, select Options, select SMS, select Message centre number and check the number entered. Programme the call to be forwarded to answer phoneusing the information provided by the operator. Go into the Settings menu, select the Energy saving menu and activate backlight Switch off and then switch phone back on. [. . . ]