User manual SANGEAN ATS-505 OPERATING INSTRUCTIONS

[. . . ] Press "ENTER" button for more than 2 seconds until " " real time symbol and 4. As you press each button, the corresponding number will show on the display. Note: Yo u m a y c h a n g e 2 4 h o u r t o 1 2 h o u r f o r m a t o r v i c e v e r s a b y p r e s s i n g M O D E a n d related buttons described later. Setting the dual time In addition to real time, a dual time can be programmed into the radio. Press ENTER button, display dual time symbol " " will flash. " will stop flashing. [. . . ] When the waveband end is reached, the radio will beep and continue tuning from the opposite waveband end. 5. Adjust the volume control for comfortable listening. Memory tuning Yo u m a y s t o r e u p t o 4 5 p r e s e t s t a t i o n s i n m e m o r y . 1 8 o n S W i n 2 p a g e s , 9 e a c h o n F M , M W a n d L W b a n d s . To s t o r e a s t a t i o n i n p r e s e t m e m o r y , p r o c e e d a s f o l l o w s . 2. Tune to the desired frequency using one of the previous described tuning methods. 6 3. Press the button marked M (memory), display M and suggested preset number will flash, press ENTER to store your station in that memory position. Select preset station that is to be changed, press memory button ( M and existing memory position will flash). W h e n p r e s e t s 1 - 9 a r e f u l l , p r e s s PA G E button to select Page 2. If all presets have been used, pushing M button will display FULL on LCD. If you still desire to store new station, push any button of 1-9 where new station is to be stored and hold for more than 2 seconds. New station will be put into memory in position selected and original station in this position will be replaced. Press the numbered button corresponding to the preset memory location for the required station. The radio will instantly tune to the station and display will show its frequency and memory location. S e l e c t S h o r t Wa v e M e t e r B a n d 1. Turn on the radio by pressing the POWER on/of button. 3. Press SW SELECT button to select the required SW meter band, display will appear low end frequency and SW meter band it belongs to. This radio covers SW 120 to 11 meter band. APS (auto Preset System) This radio provides an easy to use feature called APS (Auto Preset System) which operated on FM, MW and LW bands. P r e s s Tu n i n g U P a n d D O W N b u t t o n a t t h e s a m e t i m e f o r m o r e t h a n 2 s e c o n d s . The radio will beep and then scan from the lowest frequency on the selected band. Automatically storing stations in preset memory based on signal strength. 5. If during APS operation, no stations are found, display will show lowest frequency of selected band. T h e m a x i m u m n u m b e r o f p r e s e t i s 9 e a c h o n F M / M W / LW b a n d s . I f d u r i n g A P S operation more than 9 presets are found, there will be only 9 stations stored in the preset memories. 3. All previous stored preset stations will be erased when APS operation commences. 4. APS operation can be cancelled by pressing the POWER on/off Memory Scan This radio provides a feature called Memory Scan, when activated will scan the Preset memories. [. . . ] To release the Lock switch, move the switch to OFF position, the LOCK icon Will be removed from the display. Light Press the light button will turn on the light and illuminate the display for approx. Or you may turn it off by another press to the light button. DX/Local switch When listening to SW/FM broadcasting, this switch adjusts the receiver's sensitivity. When you listen to a strong station and the signal is slightly distorted, set the switch to the LOCAL position for best reception. For normal or weak stations, set the switch to the DX position for maximum sensitivity. SW EXT. [. . . ]