User manual SANGEAN DT300V

DON'T FORGET : ALWAYS READ THE USER GUIDE BEFORE BUYING !!!

If this document matches the user guide, instructions manual or user manual, feature sets, schematics you are looking for, download it now. Diplodocs provides you a fast and easy access to the user manual SANGEAN DT300V. We hope that this SANGEAN DT300V user guide will be useful to you.


SANGEAN DT300V : Download the complete user guide (1860 Ko)

Manual abstract: user guide SANGEAN DT300V

Detailed instructions for use are in the User's Guide.

[. . . ] Slide the cover in the direction of the arrow to gain access to the battery compartment 10 insert 2 AAA(UM-4) batteries into the compartment. Make sure that batteries are positioned in accordance with the diagram located below batteries in battery compartment. Note: [1] A low battery icon E appearing on the LCD display indicates a weak and replacement is necessary. [2] To ensure that the preset memory and time are not lost during battery replacement make sure that power on/off switch 5 is in the off position and that the batteries are replaced within 3 minutes. 6 Setting Time When batteries are installed for the first time the LCD display time digit will flash indicating that the time needs to be set. The clock can be set with the power off but the lockswitch 3 must be off. [. . . ] Speaker On/Off Switch The built-in speaker may be turned on or off using the Speaker Switch 7 . The speaker switch must be in the off position with the earphone plugged into the earphone jack to receive FM stereo programs. Stereo icon C will appear in the display. 9 Volume Control The volume may be adjusted by using the Volume Control Adjustment 1 Tuning the Radio Band Frequency AM 520-1710kHz/ 522-1629kHz FM 87. 5-108MHz Antenna Internal-Rotate radio for best reception External-Make sure earphone or pig tail antenna is inserted into earphone jack. TV CH. 2-13(VHF) External-Make sure earphone or (DT-300V/DT-300VW) pigtail antenna is inserted into earphone jack. 10 WX CH. 0-9 External-Make sure earphone or pigtail antenna is inserted into Earphone jack A. Scan Tuning Turn on the radio by pressing On/Off Button 5 . Select the desired band by pressing Band Selection Button 8 Press and hold the Tuning Control Button 13 or 14 for more than 1/2 second . The radio will start to scan and will stop at the first active station. Repeating the procedure will start the scan again. The receiver will automatically turn itself off after 90 minutes of operation or you may turn it off at anytime by pressing the On/Off Button 5 B. Manual Tuning Turn on the radio by pressing On/Off Button 5 . Desired station may be selected by either pressing the Tuning Control 13 or 14 intermittently . 11 until the desired station is reached or pressing and holding the Tuning Control 13 or 14 until the station is reached. Setting Presets Manually Turn on receiver by pressing On/Off Button 5 . Select desired band by pressing Band Selector Button 8 . Tune to the desired station using the Manual or Scan Tuning Method as described above. "Memo" flashes in the LCD display and a suggested preset position flashes. Press Memory Button 11 again if flashing position is suitable and desired station will appear in the position selected. If you would prefer to locate desired station in a position other than that suggested use Memory Selection Button 13 or 14 to move to chosen postion. After selection is complete press Memory Button again to complete Selection. You may store a total of 9 stations for each band Original stations are eliminated or exchanged when a new 12 station is selected to take its place. When the memory is full for a particular band pressing the Memory Selection Button 11 will cause all the positions to flash. press the Memory Selection Switch 11 and the original station will be eliminated and the new station will take its place. D. Selecting Memory Presets Turn on receiver by pressing On/Off Button 5 . Select desired band by pressing Band Selector Button 8 Move the Select Cursor L to the Memory Positions H by Pressing Select Button 12 . Select desired preset position using Memory Up/Down Buttons 13 or 14 E. Automatic Memory Preset System (APS) This receiver is equipped with an Automatic Memory Preset System that will automatically select. and assign positions to stations on the band you select. Turn on receiver by pressing 13 On/off Button 5 . Select desired band by pressing Band Select or Button 8 . [. . . ] Areas. 15 Mono/Stereo Button Monaural or Stereo headphone reception may be selected durning FM reception by alternately pressing the Mono/Stereo Button 9 The Speaker On/OffSwitch 7 must be in the Off Lock Switch To Prevent accidental changing of any of the radio settings move the Look Switch 3 to the locked position. When engaged in the locked position the icon key D will appear in the LCD display. To release the lock switch simply move the switch to the off position. Make sure lock Switch 3 is in off position when radio is to be used as radio is completely inoperative until lock switch is released. [. . . ]

DISCLAIMER TO DOWNLOAD THE USER GUIDE SANGEAN DT300V




Click on "Download the user Manual" at the end of this Contract if you accept its terms, the downloading of the manual SANGEAN DT300V will begin.

 

Copyright © 2015 - manualRetreiver - All Rights Reserved.
Designated trademarks and brands are the property of their respective owners.