User manual SAUNIER DUVAL THEMA CLASSIC F18E SB

[. . . ] 4000124050-2 10. 03 Instructions for Use Installation and Servicing To b e l e f t w i t h t h e u s e r Themaclassic F24E Fanned Flue Combination Boiler G. C. No. No. 41-920-35 F24E shown Hepworth Heating Ltd. , Nottingham Road, Belper, Derbyshire. DE56 1JT Guarantee Registration Thank you for installing a new Saunier Duval appliance in your home. Saunier Duval appliances' are manufactured to the very highest standard so we are pleased to offer our customers' a Comprehensive Guarantee. [. . . ] J * supplied in plastic bag Telescopic Top flue kit Diagram 10. 1 Diagram 10. 2 21 4000124050-2 11886 The Horizontal Telescopic Top Flue, Kit No. A2004500 10 Horizontal Telescopic Top Flue Installation · For flue lengths up to 0. 5m fit the restrictor (supplied in the document envelope) inside the fan outlet, see diagram 10. 3. · Remove the elbow (D) and the telescopic flue assembly (A) from the flue kit. Fit the telescopic flue assembly (A) into the prepared hole in the wall. Remove the telescopic flue assembly (A) from the prepared hole in the wall, make sure the air duct is extended to its required length. Drill , secure with two screws and tape to secure the air duct, take care not to drill the inner flue pipe. Fit the telescopic flue assembly (A) with the fitted fixing collar seal into the prepared hole in the wall. Remove the backing from the self adhesive gasket (F) and carefully fit gasket to base of flue elbow. Fit the `O' rings (H) into the grooves in the flue ducts within the elbow (D). Fit rubber sealing collar (E), into groove at the outer end of the air duct pipe (A). (If the telescopic flue has been pulled apart care must be taken not to damage the `O' ring on the flue duct when re-assembling). Pull telescopic flue assembly (A) inwards to bring rubber sealing collar hard up against external wall. Fit the fixing collar (C) using the two screws (G). STEP 1. Outside wall face FLUE LENGTH 90mm (D) (A) 17mm IMPORTANT "BUTT FIT" C L Flue centre line BOILER STEP 2. 25mm minimum Air Duct over lap (B) FIXING COLLAR 25mm SEAL (A) 2 off (G) Drill, screw 2 off and tape the Air Duct STEP 3. (D) ELBOW 4 off (G) (A) (E) EXTERNAL RUBBER SEALING COLLAR 'O' RING (H) GASKET (F) BOILER STEP 4. (D) 11874 (A) RESTRICTOR fitted for flue lengths less than 0. 5m (E) (G) 2 off (G) (A) (E) FIXING (C) COLLAR STEP 5. 2 off (D) The restrictor must be fitted to the inside of the fan outlet. Diagram 10. 3 Diagram 10. 4 4000124050-2 22 11879 10. 3 Installation of telescopic flue assembly 10a Horizontal Top Flue Installation Is suitable for installations that require a max. Note: Additional 1 metre extensions, 90° and 45° bends are available. The use of flue bends requires the maximum extended flue lengths to be reduced by 1m. for 45°. SIDE FLUE L 70mm 65mm 10a. 2 Flue systems rear and side, refer to diagram 10a. 1. 10a. 3 Flue cutting, refer to diagram 10a. 2. Important: Do not leave any burrs or sharp edges on the cut ends of the pipes. 205mm Note : Top of boiler casing not front panel 410 mm G E D A J H I C 11646 F B 20mm * refer to diagram 6. 1 Min. Clearance REAR FLUE L The flue kit 86285 comprises: - Air duct pipe . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A - Flue duct pipe . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . B - Elbow . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . C - Fixing collar seal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . D - Fixing collar . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] · Note: Take care not to damage the 'O' ring. 18. 30 Discharge safety valve, refer to diagram 18. 19. Before starting refer to the front of Section 18 Important information. · Pull out slotted metal clip from valve body and remove valve. 18. 31 (F24E Only) Three-way valve head, refer to diagram 18. 20. Before starting refer to the front of Section 18 Important information. (It will not be necessary to remove the gas control electrical cables). · Pull out slotted metal clip from valve body and remove valve head from body. [. . . ]