User manual SHARP 14J1-RU
DON'T FORGET : ALWAYS READ THE USER GUIDE BEFORE BUYING !!!
If this document matches the user guide, instructions manual or user manual, feature sets, schematics you are looking for, download it now. Diplodocs provides you a fast and easy access to the user manual SHARP 14J1-RU. We hope that this SHARP 14J1-RU user guide will be useful to you.
Manual abstract: user guide SHARP 14J1-RU
Detailed instructions for use are in the User's Guide.
[. . . ] The illustration of 21J1-RU is used in this operation manual.
POWER
MENU/
PRESET
CH
VIDEO
AUDIO
AV-2 IN
(21J1-RU)
Bottom
CH
VCR
75-ohm coaxial cable (round cable) (not supplied) Standard DIN45325 plug (IEC169-2) Antenna in
AV-1 IN
OUT AUDIO
CAUTION : DANGEROUS VOLTAGE INSIDE
AV-1 IN OUT AUDIO
TO PREVENT ELECTRIC SHOCK. NO UBER-SERVICEABLE PARTS INSIDE, REFER SERVICING TO QUALIFIED SERVICE PERSONAL.
VIDEO
CAUTION : DANGEROUS VOLTAGE INSIDE
TO PREVENT ELECTRIC SHOCK. NO UBER-SERVICEABLE PARTS INSIDE, REFER SERVICING TO QUALIFIED SERVICE PERSONAL.
VIDEO
POWER
To antenna in terminal
To RF out terminal Antenna in
POWER switch Turns on and off the main power. Power indicator Power can be turned on by the remote control when the indicator is dimly. [. . . ] /
CH
CH-SETTING POSITION COLOUR SOUND SKIP FINE CH :SELECT :ADJUST CH27 AUTO D/K OFF 168. 25MHz
TV/VIDEO
MENU/PRESET
CH
to select desired setting.
1 4
2 5 8 0
3 6 9
• Pressing
Language
MENU/PRESET
# Each time you press
SECAM D/K
CH CH
# Press
/
on TV set.
1
[ TV set (Bottom) ]
CH
/ , setting for individual items changes as follows:
7
CH CH
• All the TV stations in your area that can be received by the TV set are automatically preset between channels 1 to 99. • The screen shows whatever is on channel 1 when auto channel preset is finished.
• POSITION The channel position changes to the higher or lower number. • COLOUR
FEATURE CH-SET
TIMER NORMAL
PICTURE
CH-SET
TV
MENU/PRESET
AUTO
PAL
SECAM
N443
• SOUND
B/G I D/K
Manual channel tuning
Enables manual channel tuning to a desired TV station.
1 4 2 5 8 0
TV/VIDEO
3 6 9
!twice to display MANUAL mode
changes the screen as shown below.
MANUAL Normal screen
MANUAL(D/K) VHF 1 48. 25MHz
7
Number buttons
• SKIP ON OFF Channel numbers with a “ ” mark on the left are set to SKIP. To turn off SKIP, press the number buttons to select the desired channel and then set “SKIP” to “OFF”. • FINE The frequency changes to allow fine tuning.
CH
MENU/PRESET
CH
CH
screen.
• Pressing
Language
MENU/PRESET
CH
FEATURE CH-SET TIMER NORMAL PICTURE
AUTO
$ Press
TV
CH-SET
to return to normal screen.
CH-SETTING POSITION COLOUR AV1 AUTO
# Press $ Press
/ CH or number buttons to select channel position.
CH
• When you select AV1, AV2 for the channel position, the CH-SETTING menu changes as shown on the right and the colour mode changes in the following order:
AUTO PAL SECAM N443 N358
CH :SELECT :ADJUST
/ channel position.
on TV set to locate channel you wish to preset to current
• Search is initiated and when a TV signal is received during the search, the search stops.
% Repeat steps 3 and 4 above, to preset channel positions for other broadcasts. ^ Press
MENU/PRESET
again to display normal screen.
• AUTO PRESET stores all receivable channels including those which may be very weak and not clearly visible. / /
CH
TIMER
CH
CH
to select “ON
”.
OFF ON POSITION VOLUME
--:-8:00 ----:--
CH
FEATURE CH-SET
TIMER NORMAL
PICTURE
to set time for TV to turn
TIMER OFF ON POSITION VOLUME --:-8:00 CH28 ---:--
To more bluish background
TIMER
TV
*: TINT can only be selected and adjusted when receiving NTSC broadcasts. (AV only) • WHITE TEMP can only be adjusted on PICTURE menu.
• Maximum time that can be preset is 12 hours and 50 minutes. Timer start to count down after setting.
$ Press CH / CH to select “POSITION”. ^ Repeat step 4 to 5 above to select and set the
“VOLUME”.
TIMER OFF ON POSITION VOLUME --:-8:00 CH28 20 --:--
[ TV Set (Bottom) ]
& Press * Press
TIMER
to return to normal screen. to put TV set into Standby mode.
Power indicator (Flashing)
• Power indicator will flash to indicate On Timer is set. • When the preset length of time setting has passed, the power turns on and a picture appears on the screen. • The ON TIMER speaker volume gradually increases from zero to preset volume.
• Pressing NORMAL while a PICTURE selection is displayed, only the selected mode is reset to the standard (factorysetting) position. • Pressing NORMAL while a PICTURE menu screen is displayed will reset all the item of PICTURE menu to the standard (factory-setting) position.
• The Off timer is cancelled if the power is turned off or set to the Standby mode using on the remote control or POWER on the TV set, or if the power is otherwise interrupted. • The On Timer is cancelled if the power is turned off using POWER . • If the TV set is turned on by the On Timer, then the TV set will be automatically turned off in two hours if no buttons are pressed on the TV set or remote control.
21J1-RU[EN]
5
7/9/05, 11:22 am
E8
TIMER SETTING (Continued)
E10
USEFUL FEATURES
Reminder on-screen timer
Lets you know when a preset length of time has passed by displaying a countdown timer on the screen. This is useful for timer cooking while you watch TV.
Channel / Timer display
Displays the current channel number, the timer, and other settings on the screen.
! [. . . ] NO UBER-SERVICEABLE PARTS INSIDE, REFER SERVICING TO QUALIFIED SERVICE PERSONAL.
VIDEO
To Audio/ Video in terminals
Turn OFF using the POWER switch, then turn ON again after a minute. Adjust COLOUR control.
VCR
To Audio/ Video out terminals
Check batteries in the remote control.
Try fine tuning to correct. Contrast setting in picture mode might be all the way to the minus side. Increase the volume.
• The audiovisual cords required to connect the TV set with video equipment may differ from those shown in the above diagram. [. . . ]
DISCLAIMER TO DOWNLOAD THE USER GUIDE SHARP 14J1-RU
Click on "Download the user Manual" at the end of this Contract if you accept its terms, the downloading of the manual SHARP 14J1-RU will begin.