User manual SHARP AL-2030
DON'T FORGET : ALWAYS READ THE USER GUIDE BEFORE BUYING !!!
If this document matches the user guide, instructions manual or user manual, feature sets, schematics you are looking for, download it now. Diplodocs provides you a fast and easy access to the user manual SHARP AL-2030. We hope that this SHARP AL-2030 user guide will be useful to you.
Manual abstract: user guide SHARP AL-2030
Detailed instructions for use are in the User's Guide.
[. . . ] MODEL
AL-2030 AL-2040CS
DIGITAL MULTIFUNCTIONAL SYSTEM OPERATION MANUAL
Page
INTRODUCTION SETTING UP THE UNIT LOADING PAPER INSTALLING THE SOFTWARE MAKING COPIES SPECIAL FUNCTIONS MAINTENANCE TROUBLESHOOTING THE UNIT APPENDIX
4 7 14 19 46 52 57 61 69
AL-2030
AL-2040CS
FOR YOUR PROTECTION. . .
To aid in reporting this unit in case of loss or theft, please record below the model number and serial number located on the back of the unit. We also suggest you record all the information listed and retain for future reference. MODEL NUMBER DATE OF PURCHASE Dealer Address State Service Station Address State Zip City Telephone Zip City Telephone SERIAL NUMBER
To obtain service, or to obtain product literature, accessories, or supplies, please call 1-(630)378-3590 in the USA.
For customer assistance, please visit http://www. sharpusa. com/ (for USA) on the World Wide Web or call 1-(630)378-3590 (for USA).
Shielded interface cables must be used with this equipment to maintain compliance with EMC regulations.
Do not make copies of anything which is prohibited from copying by law. The following items are normally prohibited from copying by national law. [. . . ] It is recommended that such originals be copied from the document glass. · Special originals such as transparency film should not be fed through the SPF, but should be placed directly on the document glass. 5/32" (4mm)) can occur at the leading and trailing edges of the copies. 11/64" (4. 5mm) in total) can occur along the other edges of the copies. It can be 15/64" (6mm) (max. ) at the trailing edge of the second copy of two-sided copying. · To stop continuous copying using the SPF, press the clear key. · Copying using one-sided to one-sided mode: Ensure that no indicator is lit among the original to copy indicators.
1 2
Make sure that no original is left on the document glass. Adjust the original guides to the size of originals.
3
Set the originals face up in the document feeder tray.
Use the peep hole (see the illustration at right) to check the position of the original. Align the top edge of the original with this mark.
Original face up Peep hole
48
SET THE COPY QUANTITY
Set the number of copies using the two copy quantity ( from the document glass or copying from SPF. , ) keys when copying · Press the clear key to clear an entry if a mistake is made. · A single copy can be made with the initial setting, i. e. , when "0" is displayed. · Press the right copy quantity key to set the unit digit from 0 to 9. · Press the left copy quantity key to set the tens digit from 1 to 9.
Tens digit
Unit digit
EXPOSURE ADJUSTMENT/PHOTO COPYING
Exposure adjustment
Copy density adjustment is not required for most originals in the automatic exposure mode. To adjust the copy density manually or to copy photographs, the exposure level can be adjusted in five steps manually. (p. 55) ) mode can be
5
1
Press the exposure mode selector key to select the MANUAL ( ) mode or PHOTO ( ) mode.
2
Use the light ( ) and dark ( ) keys to adjust the exposure level. If exposure level 2 is selected, the two left-handmost indicators for that level will light up simultaneously. Also, if level 4 is selected, the two right-handmost indicators for that level will light up simultaneously.
49
Automatic exposure adjustment
This automatic exposure level will remain in effect until you change it again by this procedure. The automatic exposure level can be adjusted to suit your copying needs. This level is set for copying from the document glass and copying from the SPF respectively.
1
When adjusting the automatic exposure level for copying from the SPF, place an original in the document feeder tray and make sure that the SPF indicator lights up. When adjusting the level for copying from the document glass, make sure that no original is left in the document feeder tray. Press the exposure mode selector key to select the PHOTO ( ) mode.
2
3
Press and hold down the exposure mode selector key for approximately 5 seconds. The PHOTO ( ) indicator will go out and the AUTO indicator will begin to blink. [. . . ] 42 Scanning with the "Scanner and Camera Wizard" . . . . . . . . . . . . . . . . . . . . . . . . . 57 TD cartridge replacement required indicator. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 Prevention of OC copies when the SPF is up function . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6, 51
INDEX BY PURPOSE
Checking the package . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ]
DISCLAIMER TO DOWNLOAD THE USER GUIDE SHARP AL-2030
Click on "Download the user Manual" at the end of this Contract if you accept its terms, the downloading of the manual SHARP AL-2030 will begin.