User manual SHARP AQUOS LC-32GA5U OPERATION MANUAL

[. . . ] LC-26GA5U LC-32GA5U LIQUID CRYSTAL TELEVISION ENGLISH OPERATION MANUAL · The illustrations and on-screen displays in this operation manual are for explanation purposes and may vary slightly from the actual operations. · The examples used throughout this manual are based on the LC-26GA5U model. IMPORTANT: To aid reporting in case of loss or theft, please record the TV's model and serial numbers in the space provided. The numbers are located at the rear of the TV. Model No. : Serial No. : IMPORTANT INFORMATION WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS PRODUCT TO RAIN OR MOISTURE. The lightning flash with arrow-head symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. The exclamation point within a triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the product. CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). [. . . ] · Press ENTER to reset the image to original positions. Press c/d to select "Setup". Press a/b to select "Position", and then press ENTER. Press a/b to select "H-Pos. " or "V-Pos. ". 5 Press c/d to adjust the item to your desired position. NOTE · For resetting all adjustment items to the factory preset values, press a/b to select "Reset", and then press ENTER. · You can easily move the image position as shown on this page, but when the power is switched off the image will return to the previously memorized position. Selected item H-Pos. V-Pos. Description Centers the image by moving it to the left or right. Centers the image by moving it up or down. 33 Useful adjustment settings Auto Sync. adjustment (PC input mode only) For automatically adjusting the PC image. Fine Sync. adjustment (PC input mode only) Ordinarily you can easily adjust the picture as necessary to change image position using Auto Sync. In some cases, however, manual adjustment is needed to optimize the image. 1 2 Press MENU and the MENU screen displays. Press c/d to select "Setup". 1 2 Press MENU and the MENU screen displays. 3 Press a/b to select "Fine Sync. ", and then press ENTER. Press c/d to adjust the item to your desired position. Press c/d to select "Setup". 4 5 3 4 Press a/b to select "Auto Sync. ", and then press ENTER. Press c/d to select "Yes", and then press ENTER. · Auto Sync. starts and "Now adjusting the image" displays. NOTE · For resetting all adjustment items to the factory preset values, press a/b to select "Reset", and then press ENTER. Selected item Description Centers the image by moving it to the left or right. Adjust when characters have low contrast or when the image flickers. · · · · NOTE When Auto Sync. may fail even if "Auto Sync completed successfully" displays. may fail if the computer image has low resolution, has unclear (black) edges, or is moved while executing Auto Sync. Be sure to connect the PC to the TV and switch it on before starting Auto Sync. H-Pos. Clock Phase 34 Useful adjustment settings Input Select DVI input signal setting 1 2 Press INPUT to select INPUT5. Press MENU and the MENU screen displays. INPUT button 3 4 Press c/d to select "Option". Selecting input source Use this menu to select the input source. Press a/b to select "Input Select", and then press ENTER. Press a/b to select the equipment connected to INPUT 5 terminal, and then press ENTER. 1 Press INPUT. · A list of selectable sources appears. 5 2 Press INPUT again to select the input source. · An image from the selected source automatically displays. · If the corresponding input is not plugged in, you cannot change the input. Be sure to connect the equipment beforehand. Selecting input signal type For setting the signal type of external equipment connected to INPUT 1, 2 or 5 terminals. 1 2 3 Press MENU and the MENU screen displays. Press c/d to select "Option". Press a/b to select "Input Select", and then press ENTER. Press a/b to select a signal type you want to set, and then press ENTER. · If the selected signal type is incorrect, an image does not display or no color image displays. 4 NOTE · If you set INPUT1 and INPUT2 to Auto, the TV will automatically select the input signal. · Check the operation manual of the external equipment for the signal type. · Setting INPUT 1 and INPUT 2 signal selection to "Auto" when other equipment is connected will result in the following connectivity priority. [. . . ] In no event shall Sharp be liable, or in any way responsible, for any damages or defects in the Product which were caused by repairs or attempted repairs performed by anyone other than an authorized servicer. Nor shall Sharp be liable or in any way responsible for any incidental or consequential economic or property damage. Some states do not allow the exclusion of incidental or consequential damages, so the above exclusion may not apply to you. Model Specific Section Your Product Model Number & Description: LC-26GA5U LCD Color Television LC-32GA5U LCD Color Television (Be sure to have this information available when you need service for your Product. ) One (1) year parts and labor from the date of purchase. [. . . ]