User manual SHARP AQUOS LC-40C45U OPERATION MANUAL

[. . . ] LC-40C37U LC-40C45U LIQUID CRYSTAL TELEVISION TELEVISOR CON PANTALLA DE CRISTAL LÍQUIDO OPERATION MANUAL MANUAL DE OPERACIÓN Ó ESPAÑOL ENGLISH LC-40C37U LC-40C45U LIQUID CRYSTAL TELEVISION ENGLISH OPERATION MANUAL · The illustrations and on-screen displays in this operation manual are for explanation purposes and may vary slightly from the actual operations. · The examples used throughout this manual are based on the LC-40C37U model. IMPORTANT: To aid reporting in case of loss or theft, please record the TV's model and serial numbers in the space provided. The numbers are located at the rear of the TV. Model No. : Serial No. : IMPORTANT INFORMATION WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS PRODUCT TO RAIN OR MOISTURE. The lightning flash with arrow-head symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. The exclamation point within a triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the product. CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). [. . . ] The adjustment range of the OPC sensor can be set to a maximum of e16 and a minimum of f16. Selected item Max. Description f15 through e16 f16 through e15 NOTE · The range of OPC can only be adjusted when the OPC is set to On. · The maximum setting cannot be set to a smaller number than the minimum setting. · The minimum setting cannot be set to a bigger number than the maximum setting. · Depending on the brightness of the surrounding light, the OPC sensor might not operate if the adjustment range is small. 24 Basic adjustment settings Sound adjustment You can adjust the sound quality to your preference with the following settings. Surround Surround effects can be set using the "Audio" menu. Press MENU and the MENU screen displays. 1 2 3 1 2 Press MENU and the MENU screen displays. Press c/d to select "Audio". Press a/b to select "Surround", and then press ENTER. MENU [Audio . . . Surround] Power Control Audio Treble [ 0] [ 0] [ 0] 15 15 L 15 15 R [Off] Press c/d to select "Audio". MENU [Audio] Power Control Bass Balance Surround Reset Audio Treble Bass Balance Surround Reset [ 0] [ 0] [ 0] 15 15 L 15 15 R [Off] 4 5 Press c/d to select "On", and then press ENTER. Press MENU to exit. 3 4 Press a/b to select a specific adjustment item. Press c/d to adjust the item to the desired level. cbutton For weaker treble For weaker bass dbutton For stronger treble For stronger bass NOTE · You can choose Surround by pressing SURROUND on the remote control unit. · Audio menu is grayed out when Output Select is set to "Variable". In this case, please refer to the operation manual of your DVD player. Selected item Treble Bass Balance Decrease audio from Decrease audio from the left speaker the right speaker 5 Press MENU to exit. NOTE · Audio menu is grayed out when Output Select is set to "Variable". · For resetting all Audio adjustment items to the factory preset values, press a/b to select "Reset", press ENTER, press c/d to select "Yes", and then press ENTER. 25 Basic adjustment settings Power Control Power control setting allows you to save energy. No signal off When set to "Enable", the power will automatically shut down if there is no signal for 15 minutes. Digital Setup This setting allows you to optimize the settings of Digital broadcasting. Audio Setup You can output digital audio to an AV amplifier or similar device whose DIGITAL AUDIO INPUT terminal is connected to the DIGITAL AUDIO OUTPUT terminal on the TV. Please select an audio output format compatible with the audio format of the program you are watching and the equipment connected. 1 2 3 4 Press MENU and the MENU screen displays. Press c/d to select "Power Control". Press a/b to select "No Signal Off", and then press ENTER. Press c/d to select "Enable", and then press ENTER. 1 2 3 Press MENU and the MENU screen displays. Press c/d to select "Digital Setup". Press a/b to select "Audio Setup", and then press ENTER. Press a/b to select "PCM" or "Dolby Digital", and then press ENTER. Enable Disable 4 · Five minutes before the power shuts down, the remaining time displays every minute. PCM Dolby Digital 5 Press MENU to exit. NOTE · "Disable" is the factory preset value. · When a TV program finishes, this function may not operate. Selected item PCM Description The optical output terminal outputs audio signal in PCM form. If your digital audio system does not support Dolby Digital, select "PCM". The optical output terminal outputs audio signal in Dolby Digital form. It reproduces sound from surround program of digital. No operation off When set to "Enable", the power will automatically shut down if there is no operation for 3 hours. Dolby Digital 1 2 3 Repeat steps 1 and 2 in No signal off. Press a/b to select "No Operation Off", and then press ENTER. Press c/d to select "Enable", and then press ENTER. · Five minutes before the power shuts down, the remaining time displays every minute. 5 Press MENU to exit. 4 Press MENU to exit. NOTE · "Disable" is the factory preset value. 26 Using external equipment You can connect many types of external equipment to your TV like a DVD player, VCR, Digital TV tuner, HDMI equipment, game console or camcorder. To view external source images, select the input source from INPUT on the remote control unit or on the TV. Displaying an external equipment image This explanation is for the setting when connecting a DVD player to the INPUT1 terminal. Selecting the INPUT signal 1 2 3 4 Press MENU and the MENU screen displays. Press c/d to select "Option". Press a/b to select "Input Select", and then press ENTER. [. . . ] Also, do not leave the unit in a location exposed to direct sunlight or near a heater, as this may cause the cabinet to deform and the Liquid Crystal panel to malfunction. Storage temperature: f4°F to +140°F (f20°C to +60°C) 49 Appendix Specifications Item Model: LC-40C37U 37o Advanced Super View & BLACK TFT LCD 3, 147, 264 dots (1366 m 768 m 3 dots) American TV Standard ATSC/NTSC System VHF 2-13ch, UHF 14-69ch 1-135ch (non-scrambled channel only) Model: LC-40C45U 45o Advanced Super View & BLACK TFT LCD LCD panel Number of dots TV-standard (CCIR) TV Function Receiving Channel VHF/UHF CATV Digital Terrestrial 2-69ch Broadcast (8VSB) Digital cable* 1-135ch (non-scrambled channel only) (64/256 QAM) Audio multiplex Backlight Audio out Terminals Rear INPUT 1 INPUT 2 INPUT 3 INPUT 4 INPUT 5 ANTENNA DIGITAL AUDIO OUTPUT OUTPUT OSD language Power Requirement Power Consumption w/o stand Weight with stand Dimension (W m H m D) Accessories Operating temperature w/o stand with stand BTSC System 60, 000 hours (at Backlight Standard position) 10W m 2 AV in, COMPONENT in AV in, COMPONENT in S-VIDEO in, AV in Audio in, HDMI in with HDCP HDMI in with HDCP 75 q Unbalance, F Type m 1 for Analog (VHF/UHF/CATV) and Digital (AIR/CABLE) Optical Digital audio output m 1 (PCM/Dolby Digital) Audio out English/French/Spanish AC 120 V, 60 Hz 186 W 48. 5 lbs. /22. 0 kg 53. 8 lbs. /24. 4 kg 37 /4 m 26 /64 m 4 /8 inch 371/4 m 2835/64 m 121/64 inch 1 15 5 270 W 64. 9 lbs. /29. 4 kg 70. 6 lbs. /32. 0 kg 4353/64 m 2957/64 m 431/32 inch 4353/64 m 3163/64 m 121/64 inch Remote control unit (m1), AC cord (m1), "AAA" size battery (m2), Cable clamp (m1), Cable tie (m1), Stand unit (m1), Operation manual (m1) e32°F to e104°F (0°C to e40°C) * Emergency alert messages via Cable are unreceivable. · As part of policy of continuous improvement, SHARP reserves the right to make design and specification changes for product improvement without prior notice. The performance specification figures indicated are nominal values of production units. [. . . ]