User manual SHARP AR-M451U

[. . . ] If your copier is so marked, please read "I" for "ON" and " " for "OFF". The socket-outlet shall be installed near the equipment and shall be easily accessible. Required in IEC-950 (EN 60 950) - Europe The equipment should be installed near an accessible socket outlet for easy disconnection. Required in Appendix ZB of BS 7002 (En 60 950) -- United Kingdom MAINS PLUG WIRING INSTRUCTIONS The mains lead of this equipment is already fitted with a mains plug which is either a non-rewireable (moulded) or a rewireable type. Should the fuse need to be replaced, a BSI or ASTA approved fuse to BS1362 marked or and of the same rating as the one removed from the plug must be used. Always refit the fuse cover after replacing the fuse on the moulded plug. [. . . ] The dual page copy, job build, tandem copy, mirror image and B/W reverse functions do not require setting screens. To select a special function in one of the other two screens, use the / keys to change the screen. 2 Touch mode. SPECIAL MODES the key for the desired special Example: Selecting the shift function margin MARGIN SHIFT ERASE PAMPHLET COPY JOB BUILD 5-2 SPECIAL MODES Margin shift The margin shift function will automatically shift the text or image on the copy paper approximately 10 mm (1/2") in its initial setting. This function is convenient when stapling or binding copies with a string. NOTES G The initial setting for the margin width can be changed in the key operator programs to any value from 0 to 20 mm (0 to 1"). (Page 15 of the Key operator's guide) G When margin shift is selected, rotating copying will not operate even if the condition for rotate copying is met. GThe shift direction can be selected from right or left shift as shown in the illustration. One-sided copying Image shifted Original to the right Image shifted to the left Margin Margin Two-sided copying Original Image shifted to the right Image shifted to the left Or Margin Margin 5 the 3 Set [OK]shift amount as needed and touch the key. OK CANCEL OK SIDE 2 20) To display the special modes screen. . . See "General procedure for using special functions" on page 5-2. 1 Touch the [MARGIN SHIFT] key on the special modes screen. SPECIAL MODES MARGIN SHIFT ERASE SIDE 1 10 (0 mm 10 (0 mm 20) PAMPHLET COPY JOB BUILD The margin shift setting screen will appear. The margin shift icon ( ) will also appear in the upper left of the screen to indicate that the function is turned on. Use the and the keys to set the shift amount. The shift amount can be set from 0 to 20 mm in 1 mm (0" to 1" in 1/8") increments. 4 Touch the [OK] key on the special modes screen. You will return to the main screen of copy mode. About the steps that follow If an automatic document feeder is being used, see pages 4-7 through 4-10. To cancel the margin shift function, touch the [CANCEL] key on the margin shift setting screen. 2 Select the shift direction. Touch a shift direction key to select right or left. Blank pages may be automatically produced at the end depending on the number of the originals. G If a saddle stitch finisher is installed, copies can be stapled in two positions along the centre of copies and folded at the centre. To display the special modes screen. . . See "General procedure for using special functions" on page 5-2. 3 Select the binding position (left binding or right binding). LEFT BINDING RIGHT BINDING C SE 1 Touch the [PAMPHLET COPY] key on the special modes screen. SPECI L MODES MARGIN SHIFT ERASE PAMPHLET COPY JOB BUILD The PAMPHLET COPY setting screen will appear. The pamphlet copy icon ( , etc. ) will also appear in the upper left corner of the screen to indicate that the function is turned on. If you wish to insert a different type of paper for use as a cover, follow steps 4 through 12 below. If you do not wish to insert paper for a cover, continue from step 8 on the next page. type of originals 2 Designate the or 2-sided. copied: 1-sided ORIGINAL 1-SIDED 2-SIDED to be 4 Touch the [COVER SETTING] key. CANCEL OK Select the [2-SIDED] key if you wish to scan a two-sided original using the automatic document feeder. NG RIGHT BINDING COVER SETTING 5-6 SPECIAL MODES not you 5 Select whether oror "NO"). wish to copy on the cover ("YES" PRINT ON COVER YES NO the original in the document feeder 9 Place the document glass. (page 4-3) or on 10 Ensure that the desired paper size has been automatically selected based on the original size. To select another size paper, select the desired size and touch the AUTO A3 [AUTO IMAGE] key. The PAPER SELECT appropriate copy ratio will be selected 100% automatically based on OPY RATIO the original size and the paper size. (See steps 2 and 3 on page 4-15. ) UTO EXPOSURE 6 Select the paper tray for the cover. CANCEL OK PAPER TRAY (1) (2) TRAY2 A4 PLAIN (1)The currently selected paper tray for the cover is displayed. (2)The size and type of paper in the currently selected tray is displayed. as 11 Select any desired copy settings suchand the exposure or number of copies, then press the [START] key. In the example screen above, A4 (8-1/2" x 11") size plain paper is loaded. (In the screen example, the " TRAY2" display is the tray selection key. ) The tray selection screen appears when the tray selection key is touched. [. . . ] 1-7, 3-14, 3-17 Saddle stitch finisher . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-11, 3-14 Saddle stitch tray. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-14 8-7 INDEX Top tray . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-5, 3-7 Total count . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ]