User manual SHARP AY-XM09BE

[. . . ] Do not connect the grounding wire to gas pipe, water pipe, lightning rod or telephone grounding wire. a burning smell), stop the operation immediately and turn the circuit breaker OFF. Improper cable connection can cause the power supply cable and the electrical outlet to overheat and cause fire. Use only the manufacture recommended power supply cable for replacement. [. . . ] · When you replace the batteries, always change both batteries, and make sure they are the same type. · If the remote control does not operate properly after replacing the batteries, take out the batteries and reinstall them again after 30 seconds. · If you will not be using the unit for a long time, remove the batteries from the remote control. HOW TO USE THE REMOTE CONTROL Point the remote control towards the unit's signal receiver window and press the desired button. · Make sure there is no curtain or other object between the remote control and the unit. · The remote control can send signals from up to 7 metres away. 8 CAUTION · Do not allow the signal receiver window to receive strong direct sunlight, since it can adversely affect its operation. If the signal receiver window is exposed to direct sunlight, close a curtain to block the light. · Using a fluorescent lamp with a quick starter in the same room may interfere with transmission of the signal. · The unit can be affected by signals transmitted from the remote control of a television, VCR or other equipment used in the same room. · Do not leave the remote control in direct sunlight or near a heater. Also, protect the unit and remote control from moisture and shock which can discolour or damage them. 9 BASIC OPERATION 1 Press the MODE button to select the operation mode. AUTO HEAT COOL DRY 2 MODE TEMP. Press the ON/OFF button to start operation. · The red OPERATION lamp on the unit will light up. FAN TIMER TEMP. 2 5 3 1 4 3 Press the THERMO. button to set the desired temperature. AUTO / DRY MODE · The temperature can be changed in 1°C increments within the range of 2°C higher to 2°C lower from the temperature automatically determined by the air conditioner. HEAT / COOL MODE · The temperature can be set within the range of 18°C to 32 °C. SAVE MODE 1H FAN FULL POWER SWING CANCEL 4 Press the FAN button to set the desired fan speed. AUTO SOFT LOW HIGH · In the DRY mode, the fan speed is preset to AUTO and cannot be changed. 5 To turn off the unit, press the ON/OFF button again. · The red OPERATION lamp on the unit will turn off. 10 NOTES: This air conditioner is a multi-type, and two indoor units are connected to one outdoor unit. When the setting mode of one indoor unit differs from the other, the indoor unit operated later may not work. · When one indoor unit is operating in HEAT mode, the other unit can not operate in COOL or DRY mode. · When one indoor unit is operating in COOL or DRY mode, the other unit can not operate in HEAT mode. · When the mode of the indoor unit later operated is different from the one which is in operation, 4 seconds later, a long BEEP will be emitted, and the OPERATION lamp and TIMER lamp of the indoor unit later operated will blink alternately. This shows that the later operated unit is not working. How to rest the Blinking lamp: Change the remote control's mode and send same mode signal which the other indoor unit is operating in. · When the ONE-HOUR OFF TIMER is set while the unit is not operating, the unit will operate for an hour with the formerly set condition. · If you wish to operate the unit for another hour before the ONE-HOUR OFF TIMER activates, press the ONEHOUR OFF TIMER button again during operation. FULL POWER SWING CANCEL FULL POWER OPERATION In this operation, the air conditioner works at full power to make the room cool or warm so rapidly that you can use it just after you come home. 1 To activate the FULL POWER operation, press the FULL POWER button during operation. MODE TEMP. · The remote control will display . · The temperature display will go off. TO CANCEL FAN TIMER TEMP. Press the FULL POWER button again. · FULL POWER operation will also be cancelled when the operation mode is changed, when SAVE operation is set, or when the unit is turned off. SAVE MODE 1H FAN 1 NOTES: · You cannot set the temperature during the FULL POWER operation. · Cancel the FULL POWER operation after the room is sufficiently cool or warm. Excessive cooling or heating may affect your physical conditions. FULL POWER SWING CANCEL 13 TIMER OPERATION TIMER OFF The unit will turn off automatically according to your setting. Timer duration can be set from minimum 0. 5 hours (30 minutes) to maximum 12 hours. [. . . ] This sound is generated by the friction of the front panel and other components expanding or connecting due to a temperature change. INDOOR UNIT BECOMES WARM EVEN WHEN IDLE SWISHING NOISE The soft, swishing noise is the sound of the refrigerant flowing inside the unit. This is because the refrigerant also flows through the idle indoor unit's pipes when the other unit operated. If the unit appears to be malfunctioning, check the following points before calling for service. IF THE UNIT FAILS TO OPERATE Check to see if the circuit breaker has tripped or the fuse has blown. 18 IF THE UNIT FAILS TO COOL OR HEAT THE ROOM EFFECTIVELY Check the filters. Check the outdoor unit to make sure nothing is blocking the air inlet or outlet. A large number of people in the room can prevent the unit from achieving the desired temperature. [. . . ]