User manual SHARP CD-G7500DVD

[. . . ] If this equipment does cause harmful interference to number which are located on the rear of the unit. radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interPlease retain this information. ference by one or more of the following measures: Model number ______________________________ q Reorient or relocate the receiving antenna. Serial number ______________________________ q Increase the separation between the equipment and receiver. [. . . ] q Each time you press the button, the display will change as follows: NORMAL PHANTOM BYPASS X W W X NORMAL: The center speaker is used. BYPASS: The Dolby Pro Logic Surround mode is canceled. 5 After adjusting the speaker volume, press the TEST TONE button. Notes: q Be sure to adjust the sound from your favorite listening position. q The volume is adjusted in 1 dB steps up or down each time you press the CENTER LEVEL button or the SURROUND LEVEL button. q The volume settings for the center and rear speakers are stored in memory for future use. However, if the power is disconnected or there is a power failure, the levels will return to their initial settings. 2 3 Play the video software program. To cancel the Dolby Pro Logic Surround mode, press the BYPASS button on the main unit or the DOLBY PRO LOGIC button on the remote control until "BYPASS" appears. q The BYPASS button will light. Note: q You cannot use the Dolby Pro Logic Surround feature with headphones. 11 SETTING THE CLOCK (Main unit operation) In this example, the clock is set for the 12-hour (AM 12:00) system. MEMORY/SET POWER ON/ STAND-BY CLOCK 1 2 3 4 Press the ON/STAND-BY button to enter the stand-by mode. Within 5 seconds, press the MEMORY/SET button. TUNING/ TIME ( ) Press the TUNING/TIME (X or button to select the time display mode. (AM 12:00 - PM 11:59) "AM 0:00" The 12-hour display will appear. (AM 0:00 - PM 11:59) "0:00" The 24-hour display will appear. (It is not necessary to press the 0/R (0R) button. ) q When one of the disc number buttons ( 1- 3) is pressed during playback, playback of the selected disc will begin automatically. (It is not necessary to press the 0/R (0R) button. ) DISC SKIP s APSS (Auto Program Search System) APSS automatically locates the beginning of any track. To listen again to the track being played: Press the 5 button for less than 0. 5 seconds during playback. To move to the beginning of the next track: Press the 4 button for less than 0. 5 seconds during playback. q To skip a number of tracks at one time, press the 5 or 4 button repeatedly until the desired track number is shown. q To start playing at a desired track, press the 5 or 4 button while in the stop mode to select the track number, and then press the 0/R (0R) button. Note: q APSS can only search for music on a single disc. CD RANDOM DISC SKIP s Cue and review 1 2 3 Load a disc and begin playback. Hold down the 2 button for audible fast forward, and hold down the 3 button for audible fast reverse. Caution: q Do not carry the unit with discs left in the disc trays. The discs may come loose inside the unit and they may be damaged or cause damage to the unit. q If the power fails while the tray is open, wait until the power is restored. q If the disc tray is stopped forcibly, "ERR" will appear in the display and the unit will not function. [. . . ] q After long use, the deck's heads and capstans may become magnetized, causing poor sound. Demagnetize these parts once every 30 hours of playing/recording time by using a commercial tape head demagnetizer. q In order to ensure proper operation of the CD player, preventative maintenance (cleaning of the Laser Pick-up lens) should be performed periodically in order to keep the lens dust-free. Contact your local CD software dealer for options. TAPE 2 s External care q Periodically wipe the cabinet with a soft cloth and a diluted soap solution, then wipe with a dry cloth. [. . . ]