User manual SHARP FO-775L

[. . . ] 11. Installation Setting Up and Using OpenLCR Sending Documents Receiving Documents Making Copies Making Telephone Calls Answering Machine Hookup Special Functions Printing Lists Maintenance Troubleshooting open LCR www. OpenLCR. com WARNING - FCC Regulations state that any unauthorized changes or modifications to this equipment not expressly approved by the manufacturer could void the user's authority to operate this equipment. Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. [. . . ] If you are on a touch-tone phone, you can prevent this by pressing any three keys on the phone immediately after you answer. (Note: Do not enter the code to activate fax reception: 5, * , * . ) Chain Dialing After lifting the handset, you can dial any combination of Normal Dialing, Rapid Key Dialing and Speed Dialing numbers. For example, if you have stored an area code or an access code for a special service in a Rapid Key, you can press the Rapid Key for that area code or access code, then dial the remainder of the number by pressing a Rapid Key, pressing number keys, or pressing the SPEED DIAL key and entering a two-digit Speed Dial number. Searching for an auto-dial number You can use the HOLD/SEARCH key to search for a Rapid Key or Speed Dial number. First search for the number as described in Searching for an auto-dial number on page 68, then pick up the handset or press the SPEAKER key. The number will be dialed automatically (do not press the START/MEMORY key). Redial The last number dialed can be redialed by pressing the REDIAL key (it is not necessary to pick up the handset or press the SPEAKER key). When the other party answers, pick up the handset to talk. 86 Making Telephone Calls Hold You can put the other party on hold during a conversation by pressing the HOLD/SEARCH key. You can put the handset back in the cradle without breaking the connection. If you did not put the handset back in the cradle, press the HOLD/SEARCH key again to resume conversation. 87 6. Answering Machine Hookup Connecting an Answering Machine If desired, you can connect an answering machine to your fax machine's TEL. This will allow you to receive both voice messages and faxes when you are out. 1 Remove the seal covering the TEL. SET jack. 2 Connect the answering machine's telephone line jack to the TEL. · If desired, you can connect an extension phone to your answering machine's extension phone jack. TEL. To answering machine's telephone line jack. 88 Connecting an Answering Machine Changing the outgoing message The outgoing message (OGM) of your answering machine should be changed to inform callers who want to send a fax to press their Start key. Please leave a message after the beep or press your facsimile Start key to send a fax. Thank you for calling. " Try to keep the length of the message under 10 seconds. If it is too long, you may have difficulty receiving faxes sent by automatic dialing. If your outgoing message must be longer than 10 seconds, leave a pause of about four seconds at the beginning of the message. This will give your fax a chance to detect fax tones sent when automatic dialing is used. Activating the answering machine connection Before you go out, activate the answering machine connection as follows: 1 Set the reception mode to A. M. RECEPTION MODE TEL FAX A. M. 89 7. Answering Machine Connecting an Answering Machine 2 Set your answering machine to auto answer. Your answering machine must be set to answer on a maximum of two rings. [. . . ] The classification is based upon the development of lung tumors in rats receiving chronic inhalation exposures to free carbon black at levels that induce particle overload of the lung. Studies performed in animal models other than rats did not show any association between carbon black and lung tumors. Signs and Symptoms of Exposure : not applicable Medical Conditions Generally Aggravated by Exposure : not applicable Emergency and First Aid Procedures : not applicable 148 SHARP Date Revised: . Physical Chemical Characteristics Boiling/Melting Point Vapor Pressure Vapor Density Evaporation Rate Appearance Odor m. p. [. . . ]