User manual SHARP FODC600

[. . . ] MODEL FO-DC500/FO-DC525 FO-DC600 DOCUMENT COMMUNICATION SYSTEM OPERATION MANUAL 1. Installation Sending and Receiving Documents Network Scanner Option Network Printer Option Making Copies Special Functions Optional Settings Printing Lists and Reports Maintenance Troubleshooting U. S. A. WARNING - FCC Regulations state that any unauthorized changes or modifications to this equipment not expressly approved by the manufacturer could void the user's authority to operate this equipment. Note: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. [. . . ] To check the IP address, follow the procedure in Printing out the Network Settings on page 79. 122 Installing the Printer Driver Network types There are two types of networks, a peer to peer network where you print directly to the printer without going through a server, and a client-server network where you print through a server. Follow the appropriate instructions below for your operating system and your network type to install the printer driver. Client-server network: Installing the printer driver in the server To use the printer on a client-server network, the printer driver must first be installed in the server (this must be done before installing the printer driver in client computers). Follow the appropriate procedure for your server's operating system. 1 2 3 Click the Windows Start button, point to Settings, and then click on Printers. Double-click Add Printer in the Printers window to run the Add Printer Wizard and then click Next. Make sure that "Automatically detect and install my Plug and Play printer" is not selected and click Next. 123 4. Network Printer Windows 2000 Server Installing the Printer Driver 4 Select "Create a new port" and select "Standard TCP/IP Port" from the list. Click Next. 5 6 The "Add Standard TCP/IP Printer Port Wizard" will appear. Click Next. Enter the IP address of the printer (the port name is filled in automatically). · If you need to check the IP address, follow the procedure in Printing out the Network Settings on page 79. Make sure that the printer has been turned on and has been configured for network printing, and then click the Next button. 124 Installing the Printer Driver 7 Select Custom and then click the Settings button. 8 The "Configure Standard TCP/IP Port Monitor" window will appear. Network Printer Installing the Printer Driver 9 Click the Next button. 10 11 12 13 14 Check your settings and then click the Finish button. The Add Printer Wizard will display a list of printer models and manufacturers. If the "Readme First" window appears, click Cancel to close the window. Enter the path Q:\Option\English\2kxp_pclxl (substitute the letter of your CD-ROM drive for "Q") and click the OK button. Click Next. 126 Installing the Printer Driver 15 Follow the instructions on your screen. If you would like to change the name, enter a new name (this must be 8 characters or less to allow sharing with Windows 98/Me computers). Click Next. 16 Enter a location and comment if desired, click Next, and then follow the instructions on your screen to finish installing the printer driver. · If the following window appears at any time, click Yes to continue the installation. 127 4. Network Printer Installing the Printer Driver Windows NT Server 1 2 The first step is to install Microsoft TCP/IP Printing. Click the Windows Start button, point to Settings, and then click on Control Panel. In the Control Panel window, double-click Network to open the Network window. If "Microsoft TCP/IP Printing" already appears in the list, close the Network window and go to Step 6. If "Microsoft TCP/IP Printing" does not appear, click the Add button. 3 The "Select Network Service" window shows a list of services. Select "Microsoft TCP/TP Printing", and click the OK button. 128 Installing the Printer Driver 4 5 6 7 8 9 Insert your Windows NT Server 4. 0 CD-ROM into your CD-ROM drive. The next step is to install the printer driver using the Add Printer Wizard. Click the Start button, point to Settings, and then click on Printers. Double-click Add Printer in the Printers window to run the Add Printer Wizard. [. . . ] (Remarque : Pour la composition normale et la composition directe au clavier, vous pouvez également charger le document après avoir procédé à la composition du numéro. ) Pressez les touches nécessaire. RESOLUTION ENREGISTREMENT DE NUMÉROS DE TÉLÉCOPIEURS À COMPOSITION AUTOMATIQUE 1. Pressez la touche MENU et ensuite ou jusqu'à ce que ENTRY MODE soit sélectionné à l'écran. START/ ENTER ou CONTRAST si . Pressez la touche START/ ENTER . Numérotation Normale 1. Décrochez le combiné du téléphone supplémentaire ou pressez la touche SPEAKER . 5. [. . . ]