User manual SHARP HT-CN500DVE

[. . . ] Allinterno dellapparecchio ci sono tensioni pericolose, per cui si deve sempre staccare la spina del cavo dalimentazione dalla presa di corrente prima di qualsiasi intervento di manutenzione e quando non si usa lapparecchio per un lungo periodo di tempo. Wanneer de ON/STAND-BY toets in de STAND-BY stand staat, loopt er nog steeds stroom (netspanning) in het toestel. Wanneer de ON/STAND-BY toets in de STAND-BY stand staat, kan het toestel ingeschakeld worden via de timerfunctie of de afstandsbediening. Waarschuwing: Dit toestel bevat geen door de gebruiker te repareren onderdelen. [. . . ] Volume ring light and display bright Volume ring light off and display dim Volume ring light off and display gets dimmer Notes: When sound from the subwoofer is distorted, decrease the subwoofer level. When changing the subwoofer level, the output level of the SUBWOOFER PRE OUT is also changed. Function When the FUNCTION button on main unit is pressed, the current function will change to different mode. Press the FUNCTION button repeatedly to select desired function. DVD/CD SCART USB AUX IN TUNER OPTICAL 2 OPTICAL 1 Auto power off function In the stop mode of discs/USB operation, the main unit enters the stand-by mode after 15 minutes of inactivity. Note: The backup function will protect the memorised function mode for a few hours should there be a power failure or the AC power lead becomes disconnected. E-28 Basic Operation HT-DV40H HT-DV50H Setting the clock (Remote Control only) 5 1 4 7 0 2 5 8 +10 3 6 9 ENGLISH Press the or button to adjust the hour and then press the MEMORY/DIMMER button. Press the or button once to advance the time by 1 hour. Hold it down to advance continuously. 6 Press the or button to adjust the minutes and then press the MEMORY/DIMMER button. Basic Operation In this example, the clock is set for the 24-hour (0:00) display. Press the or button once to advance the time by 1 minute. To confirm the time display: [When the unit is in the stand-by mode] Press the CLOCK/TIMER button. Note: The "CLOCK" will appear or time will flash to confirm the time display when the AC power supply is restored after a power failure or unplugging the unit. To readjust the clock: Perform "Setting the clock" from step 1. If the "CLOCK" does not appear in step 3, step 4 (for selecting the 24-hour or 12-hour display) will be skipped. To change the 24-hour or 12-hour display: 1 Clear all the programmed contents. [Refer to "Factory reset, clearing all memory" on page 63 for details. ] 2 Perform "Setting the clock" from step 1. 1 2 3 Press the ON/STAND-BY button to turn the power on. Within 10 seconds, press the or button to select "CLOCK", and press the MEMORY/DIMMER button. 4 Press the or button to select 24-hour or 12-hour display and then press the MEMORY/DIMMER button. "0:00" "AM 12:00" "AM 0:00" The 24-hour display will appear. When headphone is inserted, DVS setting and BASS/TREBLE setting, set earlier by user will be cancelled. However the DVS setting will not be recovered when the headphone is unplugged. HT-DV40H HT-DV50H Audistry sound mode ON The Dolby Virtual Speaker creates multichannel-like sound effects. Compared with the cinema mode, the bass sound level is slightly reduced. The Dolby Pro Logic indicator also lights up if 2ch sound signals are detected. Press it again to cancel. ENGLISH 3 1 2 5 8 +10 3 6 9 6 4 7 0 9 OFF The Dolby Virtual Speaker is deactivated. Possible combinations SOUND SPACE When you select "SOUND SPACE" When you select "NATURAL BASS" When you select "INTELLIGENT VOLUME" When you select "MONO TO STEREO" When you select "DVS" NATURAL BASS :Enabled :Disabled INTELLIGENT MONO TO VOLUME STEREO E-32 Basic Operation HT-DV40H HT-DV50H Enjoying surround sound (sound mode) (continued) SOUND SPACE (Sound stage expansion) The 4 speakers create spacious stereo sounds. (The SOUND SPACE indicator lights up. ) NATURAL BASS (Bass sound expansion) The system's low-frequency characteristics realise the optimal bass sounds. (The NATURAL BASS indicator lights up. ) INTELLIGENT VOLUME (Peak limiter and expander) Appropriate listener-friendly volumes realised; the volume is decreased during loud sounds, and increased during low sounds. (The INTELLIGENT VOLUME indicator lights up. ) MONO TO STEREO (Mono Stereo conversion) You can enjoy monaural sound sources with a stereo-like effect. Notes: When setting each mode of Audistry to "ON", the preset sound mode setting is cancelled. When setting the SOUND SPACE or MONO TO STEREO mode to "ON", the DVS setting is also cancelled. (It is not cancelled even if the NATURAL BASS or INTELLIGENT VOLUME mode is set to "ON". ) ENGLISH Basic Operation E-33 (The MONO TO STEREO indicator lights up. ) Playing a disc Turn on the TV, and switch the input to the "VIDEO 1", "VIDEO 2", etc. [. . . ] Note: If neither operation above restores the unit, clear all the memory by resetting it. ENGLISH Before transporting the unit Remove the CD from the unit. Carrying the unit with disc left inside can damage the unit. Factory reset, clearing all memory 1 2 Press the ON/STAND-BY button to enter the power stand-by mode. Whilst pressing down the button, press the ON/STAND-BY button until "CLEAR ALL" appears. Tuner Symptom The radio makes unusual noises continuously. Move the aerial away from the AC power lead if it is located nearby. References Condensation Sudden temperature changes, storage or operation in an extremely humid environment may cause condensation inside the cabinet (CD pickup, etc. ) or on the transmitter on the remote control. [. . . ]