User manual SHARP IM-DR420

[. . . ] IM-DR420H(E) TINSE0554AWZZ 1 1-BIT PORTABLE MINIDISC RECORDER MODEL IM-DR420H OPERATION MANUAL If you require any advice or assistance regarding your Sharp product, please visit our web-site www. sharp. co. uk/customersupport. Customers without Internet access may telephone 08705 274277 during office hours (or (01) 676 0648 if telephoning from Ireland). 0101 Thank you for purchasing this SHARP product. It will guide you in operating your SHARP product. TINSE0554AWZZ 03G R YT 1 E IM-DR420H(E) (TINSE0554AWZZ) IM-DR420H Special Notes !AND IRELAND Important Introduction -Special Notes- SERVICE INFORMATION In the unlikely event of your equipment requiring repair, please use the supplied postage paid label to send your unit to the Sharp repair centre or contact the dealer or supplier from whom it was purchased. [. . . ] When a sound, such as person speaking, is picked up by the microphone, recording will begin automatically. " Insert the plug firmly. " Use a microphone with a 3. 5 mm (1/8") diameter stereo mini plug. " If the unit starts recording too often from low unwanted noises, set the microphone input to "MIC SYNC L". Noise pickup may occur. 31 IM-DR420H(E) TINSE0554AWZZ 03/7/21 IM-DR420H_UK_4. fm IM-DR420H Recording from a Microphone (continued) !Track intervals When recording from the microphone, track numbers will be created automatically at regular intervals (default setting: approximately every 5 minutes). During a mic synchro recording, the unit pauses when a silence lasts for 3 seconds or more, and creates a track number. 5 6 Press the MENU/ENTER button. The mode will be set automatically after 7 seconds even if the MENU/ENTER button is not pressed. Track numbers will be created automatically at regular intervals. -Recording from a Microphone- Changing intervals between tracks Example: Set to "5 minutes". Useful Features 1 2 3 4 Press the MENU/ENTER button. Press the or button. During a mic manual recording Timed auto marks will be created every 5 minutes. Track number 1 5 minutes Track number 2 5 minutes Track number 3 5 minutes Track number 4 During a mic synchro recording (No automatic track numbers are created. ) (A new track number is created every 3 minutes. ) If a silence lasts for 3 seconds or more, a timed auto mark will be created 5 minutes after the previous mark is created. : Track number which is created by the timed auto mark function. : Track number which is created when a silence lasts for 3 seconds or more during synchro recording. (A new track number is created every 5 minutes. ) (A new track number is created every 10 minutes. ) Track Track number 1 number 2 2 minutes 5 minutes Track Track number 3 number 4 1 minute 5 minutes Track number 5 The interval between marks may vary slightly compared with the actual recording time. Creating track numbers manually " Press the REC button whilst recording. " The BASS button on the remote control can also be used to add track numbers. 32 IM-DR420H(E) TINSE0554AWZZ 03/7/21 IM-DR420H_UK_4. fm Changing Default Settings Whilst in the stop mode . . . IM-DR420H !Beep sound You can eliminate the confirmation sound that beeps when you press a button. 1 2 3 4 5 With a MiniDisc inserted, press the MENU/ ENTER button for 2 seconds or more. "SET UP" will appear. When you release the button, "BEEP" will flash. !Auto play You can make the unit not play automatically when you insert a playback-only MiniDisc or an accidental erasure protected MiniDisc. Press the or button to select the menu. Useful Features !Auto power save When the unit is used in a place exposed to much vibration, sound skipping can be decreased by cancelling the auto power save function. (Battery will drain faster. ) -Changing Default Settings- Press the MENU/ENTER button to display the setting item. MENU SETTING ITEM BEEP ON* BEEP OFF A-PLAY ON* A-PLAY OFF Beep Silent Set. Cancelled. 5 What is auto power save function? BEEP (Confirmation sound) AUTO PLAY (Auto play) POWER SAVE (Auto power save) D-LEVEL (Digital recording level) During playback, maximum 40 seconds (in stereo) of musical information is stored. Auto power save function automatically adjusts the storage time between 5 and 40 seconds to reduce the power consumption. " If this unit is used with the AC adaptor, the storage time will be 40 seconds regardless of the settings. " The storage time varies depending on the recording mode. 6 5 4 3 2 1 AUTO Psave* Set. Digital recording level "D. L MODE 1" The digital recording level you set will be kept even after cancelling recording. "D. L MODE 2" Every time you cancel recording, the level will return to [D. L 0dB]. (*) indicates default setting. 33 IM-DR420H(E) TINSE0554AWZZ 03/7/21 IM-DR420H_UK_4. fm IM-DR420H Checking Displays !To check the elapsed time and remaining time of the track 1 2 3 4 ! [. . . ] The condensation should evaporate and the unit will work properly. 55 IM-DR420H(E) TINSE0554AWZZ 03/7/21 IM-DR420H_UK_6. fm IM-DR420H Specifications As a part of our policy of continuous improvement, SHARP reserves the right to make design and specification changes for product improvement without prior notice. The performance specification figures indicated are nominal values of production units. Power source: Power consumption: Output power: DC 1. 2 V: Rechargeable Nickel-Metal Hydride Battery (AD-N70BT) x 1 DC 3 V: AC adaptor (AC 110 - 240 V, 50/60 Hz) DC 1. 5 V: Commercially available, "AA" size (LR6), alkaline battery x 1 60 mA (AC adaptor) RMS: 16 mW (8 mW + 8 mW) (0. 2 % T. H. D. ) Approx. 5. 4 hours (fully charged)(When using the AC adaptor included with the unit) Width: 83 mm (3-9/32") Height: 28 mm (1-1/8") Depth: 76 mm (3") Excluding the projection around the USB connection terminal 143 g (0. 32 lbs. ) with rechargeable battery Line/optical digital, microphone (powered by the main unit) Earphones (impedance: 32 ohms)/remote control Portable MiniDisc recorder Non-contact, 3-beam semiconductor laser pickup Stereo 2 channels/monaural 1 channel 20 - 20, 000 Hz ( 3 dB) Approx. [. . . ]