User manual SHARP LC-26D6U

[. . . ] Under no circumstances should the cut-off plug be inserted elsewhere into a 13A socket outlet, as a serious electric shock may occur. To fit an appropriate plug to the mains lead, follow the instructions below: IMPORTANT: The wires in the mains lead are coloured in accordance with the following code: Blue: Neutral Brown: Live As the colours of the wires in the mains lead of this product may not correspond with the coloured markings identifying the terminals in your plug, proceed as follows: · The wire which is coloured blue must be connected to the plug terminal which is marked N or coloured black. · The wire which is coloured brown must be connected to the plug terminal which is marked L or coloured red. Ensure that neither the brown nor the blue wire is connected to the earth terminal in your three-pin plug. [. . . ] Repeat the steps 6 and 7 until all desired channels are sorted. 5 Press c/d to select "Yes", and then press OK to erase the selected programme. Erase programme menus 01 SAT. 1 6 01 SAT. 1 02 Pro7 07 12 17 03 KABEL 08 13 18 Next 04 09 14 19 05 10 15 20 Sort menus 01 SAT. 1 06 11 16 01 SAT. 1 06 02 KABEL 03 04 05 02 Pro7 Next 01 SAT. 1 06 11 02 Pro7 07 12 17 03 KABEL 08 13 18 Next 04 09 14 19 05 10 15 20 01 SAT. 1 02 KABEL 16 01 SAT. 1 02 KABEL 02 KABEL Next 01 SAT. 1 06 11 01 KABEL 02 KABEL 07 12 17 03 08 13 18 Next 04 09 14 19 05 10 15 20 16 01 KABEL 02 SAT. 1 Next 23 Basic adjustment settings Language setting for on-screen display You can also select a language from setup menu. Select from among 13 languages. OPC setting Automatically adjusts the brightness of the screen. Using OPC on the remote control unit 1 2 Press MENU and the MENU screen displays. Press c/d to select "Setup". Press a/b/c/d to select the desired language listed on the screen, and then press OK. 3 4 Press OPC to switch the Optical Picture Control on and off. Using OPC on the menu screen Language list Dutch English Finnish French German Greek Italian Polish Portuguese Russian Spanish Swedish Turkish 1 2 3 Press MENU and the MENU screen displays. Press c/d to select "Picture". Press a/b to select "OPC". 4 NOTE Press c/d to select "On". · When set to "On", the System senses the surrounding light and automatically adjusts the backlight brightness. Make sure no object obstructs the OPC sensor, which could affect its ability to sense surrounding light. Selected item Off On Description The brightness is fixed at the value set in "Backlight" (see page 25). Automatically adjusts 24 Basic adjustment settings Picture adjustments Adjust the picture to your preference with the following picture settings. 1 Press MENU and the MENU screen displays. 2 3 Press c/d to select "Picture". Press a/b to select a specific adjustment item. Press c/d to adjust the item to your desired position. 4 NOTE · For resetting all adjustment items to the factory preset values, press a/b to select "Reset", and then press OK. Adjustments items for AV source MENU [Picture] Audio Picture Adjustments items for PC source MENU [Picture] Audio Picture USER [TV] OPC Backlight Contrast [+8] [+30] Off ­8 0 ­30 ­30 ­30 ­10 On +8 +40 +30 +30 +30 +10 USER [PC] OPC Backlight Contrast [+8] [+30] Off ­8 0 ­30 ­30 ­30 ­30 On +8 +40 +30 +30 +30 +30 Brightness [0] Colour Tint [0] [0] Brightness [0] Red Green Blue Advanced Reset [0] [0] [0] Sharpness [0] Advanced Reset Selected item Backlight Contrast Brightness Colour Tint Sharpness cbutton The screen dims dbutton The screen brightens Selected item Backlight Contrast Brightness Red Green Blue cbutton The screen dims dbutton The screen brightens For less contrast For more contrast For less contrast For more contrast For less brightness For less colour intensity Skin tones become purplish For less sharpness For more brightness For more colour intensity Skin tones become greenish For more sharpness For less brightness For more brightness For weaker red For stronger red For weaker green For stronger green For weaker blue For stronger blue NOTE · Select "Advanced" and then press OK to set "C. M. S-Hue", "C. M. S-Saturation", "C. M. S-Value", "Colour Temp", "Black", "3D-Y/C", "Monochrome", "Film Mode" or "I/P Setting". See pages 26 and 27. NOTE · Select "Advanced" and then press OK to set "C. M. S-Hue", "C. M. S-Saturation" and "C. M. S-Value". 25 Basic adjustment settings C. M. S. (Colour Management System) Colour tone is managed using the six-colour adjustment setting. Colour temperature Adjusts the colour temperature to give the best white image. 1 2 3 4 1 Press MENU and the MENU screen displays. Power management When set, the power will automatically shut down. Power control for AV source No signal off When set to "Enable", the power will automatically shut down if no signal inputs for 15 minutes. 1 Press MENU and the MENU screen displays. 1 2 3 4 Press MENU and the MENU screen displays. 2 3 4 Press c/d to select "Power Control". Press c/d to select "Power Control". Press a/b to select "Power Management", and then press OK. Press a/b to select "Mode1" or "Mode2", and then press OK. Description · No power management · Factory preset value. · Even if you start using the PC and the signal inputs again, the TV stays off. · The TV turns on again by pressing a on the Display or B on the remote control unit. (See page 13. ) · If no signal inputs for 8 seconds, the power shuts down. · When you start using the PC and the signal inputs again, the TV turns on. · The TV turns on again by pressing a on the Display or B on the remote control unit. (See page 13. ) Press a/b to select "No Signal Off", and then press OK. Press c/d to select "Enable", and then press OK. · Five minutes before the power shuts down, remaining time displays every minute. Selected item Off NOTE · "Disable" is factory preset value. · When a TV programme finishes, this function may not operate. Mode1 No Operation off When set to "Enable", the power will automatically shut down if there is no operation for 3 hours. Mode2 1 2 3 Press MENU and the MENU screen displays. Press c/d to select "Power Control". Press a/b to select "No Operation Off", and then press OK. Press c/d to select "Enable", and then press OK. · Five minutes before the power shuts down, remaining time displays every minute. 4 NOTE · "Disable" is factory preset value. 29 Using external equipment You can connect many types of external equipment to your TV, like a decoder, VCR, DVD player, PC, game console and camcorder. [. . . ] Also, do not leave the unit in a location exposed to direct sunlight or near a heater, as this may cause the cabinet to deform and the LCD panel to malfunction. Storage temperature: ­20°C to +60°C (­4°F to +140°F). 50 Appendix PC compatibility chart PC/MAC PC Resolution 640 x 400 720 x 400 VGA 640 x 480 WVGA 848 x 480 Horizontal Frequency Vertical Frequency 31. 5 kHz 37. 9 kHz 31. 5 kHz 37. 9 kHz 31. 5 kHz 37. 9 kHz 37. 5 kHz 43. 3 kHz 31. 5 kHz 35. 1 kHz 37. 9 kHz 48. 1 kHz 46. 9 kHz 53. 7 kHz 48. 4 kHz 56. 5 kHz 60. 0 kHz 68. 7 kHz 45. 0 kHz 48. 1 kHz 48. 4 kHz 64. 0 kHz 34. 9 kHz 49. 7 kHz 60. 2 kHz 60 Hz 85 Hz 60 Hz 85 Hz 60 Hz 72 Hz 75 Hz 85 Hz 60 Hz 56 Hz 60 Hz 72 Hz 75 Hz 85 Hz 60 Hz 70 Hz 75 Hz 85 Hz 60 Hz 60 Hz 60 Hz 60 Hz 67 Hz 75 Hz 75 Hz VESA Standard O O O O O O O O O O O O O O O SVGA 800 x 600 XGA 1024 x 768 1280 x 720 1280 x 768 1366 x 768 1280 x 1024 640 x 480 832 x 624 1024 x 768 WXGA SXGA VGA SVGA XGA O MAC13" MAC16" MAC19" Apple and Macintosh are registered trademarks of Apple Computer, Inc. DDC is a registered trademark of Video Electronics Standards Association. VGA and XGA are registered trademarks of International Business Machines Co. , Inc. 51 Appendix RS-232C port specifications PC Control of the System · When a program is set, the display can be controlled from the PC using the RS-232C terminal. [. . . ]