User manual SHARP LC-26SH7E

[. . . ] Under no circumstances should the cut-off plug be inserted elsewhere into a 13A socket outlet, as a serious electric shock may occur. To fit an appropriate plug to the mains lead, follow the instructions below: IMPORTANT: The wires in the mains lead are coloured in accordance with the following code: Blue: Neutral Brown: Live As the colours of the wires in the mains lead of this product may not correspond with the coloured markings identifying the terminals in your plug, proceed as follows: · The wire which is coloured blue must be connected to the plug terminal which is marked N or coloured black. · The wire which is coloured brown must be connected to the plug terminal which is marked L or coloured red. Ensure that neither the brown nor the blue wire is connected to the earth terminal in your three-pin plug. [. . . ] Press a/b to select "HDMI Setup", and then press OK. · "HDMI Setup" is displayed only when "EXT6" or "EXT7" is selected from the INPUT SOURCE menu. MENU [Option . . . HDMI Setup] 2 3 4 NOTE · If no (colour) image displays, try to change the other signal type. · Check the operation manual of the external equipment for the signal type. · TV, EXT3, EXT4, EXT5, EXT6 and EXT7 are not displayed in Input Select. · If both CVBS and RGB signals are input to EXT 1 or EXT 2 using a SCART cable, the TV may output an RGB signal even though you have designated CVBS for the respective terminal. This happens due to the setting of your external equipment. Colour System TV/AV only Option Audio Only DNR HDMI Setup [Off] Menu Operation: A (page 12) You can change the colour system to one that is compatible with the image on the screen. (AUTO, PAL, SECAM, NTSC3. 58, NTSC4. 43, PAL-60) NOTE · Factory preset value is "AUTO". · If "AUTO" is selected, colour system for each channel is automatically set. If an image does not display clearly, select another colour system (e. g. · "NTSC3. 58", "NTSC4. 43" and "PAL-60" cannot be selected in TV tuner mode. 5 6 Press a/b to select the desired item, and then press OK. Press a/b/c/d to select the desired setting, and then press OK. Selectable items RGB/YCbCr 4:4:4/ YCbCr 4:2:2 ITU601/ITU709 Description Select the video signal type from the HDMI terminal. News, weather and sports information, stock exchange prices and programme previews are among the many services available. 4 Turning on and off Teletext 1 2 3 Select a TV channel or external input source providing the Teletext programme. Press m again to display the Teletext on the right screen and normal image on the left screen. · Each time you press m, the screen switches as shown below. DATA* TELETEXT NOTE · The time display cannot be stored once the power is turned off. · If acquired successfully, the time information will appear in the upper-right corner of the screen by pressing MENU. Button functions Buttons P (r/s) Colour (Red/ Green/Yellow/ Blue) Description Increase or decrease the page number. Select a group or block of pages displayed in the coloured brackets at the bottom of the screen by pressing the corresponding Colour (Red/Green/Yellow/Blue) on the remote control unit. Directly select any page from 100 to 899 by using 0­9. 0­9 Reveal or hide hidden information such as an k (Reveal hidden Teletext) answer to a quiz. 3 (Freeze/ Hold) [ (Subtitle for Teletext) Stop updating Teletext pages automatically or release the hold mode. · Subtitle will not be displayed when the service does not contain the subtitle information. User for LC-26SH7E: · Subtitle is set to off when the power is turned on. User for LC-26D44S: · Subtitle is set to on when the power is turned on. · These two buttons are shown on the screen by the signs l and k. TELETEXT * May appear in DTV input mode. · If you select a programme with no Teletext signal, "No Teletext available. " displays. [. . . ] ? Communication conditions Set the RS-232C communications settings on the PC to match the TV's communications conditions. The TV's communications settings are as follows: Baud rate: Data length: Parity bit: Stop bit: Flow control: 9, 600 bps 8 bits None 1 bit None Response code format Normal response O K Return code (0DH) Problem response (communication error or incorrect command) E R R Return code (0DH) 33 Appendix Commands CONTROL ITEM POWER SETTING INPUT SELECTION A COMMAND POWR I I I I I CHANNEL T T D A A GD V T V V D V D D PARAMETER 0 _ _ _ * ?CONTROL CONTENTS POWER OFF INPUT SWITCHING (Toggle) TV (CHANNEL FIXED) DTV (CHANNEL FIXED) EXT1 ­ 7 (1 ­ 7) 1 to 7, ERR (TV/DTV) TV DIRECT CHANNEL (1 ­ 99) 1 to 99 CHANNEL UP CHANNEL DOWN DTV DIRECT CHANNEL (1 to 999) 1 to 999 DTV CHANNEL UP DTV CHANNEL DOWN EXT1 (Y/C) EXT1 (CVBS) EXT1 (RGB) 0 to 2 EXT2 (Y/C) EXT2 (CVBS) EXT2 (RGB) 0 to 2 EXT3 EXT4 EXT5 (COMPONENT) EXT6 (HDMI) EXT7 (HDMI) AV MODE SELECTION (Toggle) STANDARD SOFT ECO USER DYNAMIC 1 to 5 VOLUME (0 ­ 60) 0 to 60 TEXT SLEEP TIMER O O O O O O O T T T F F F F F F F E E E TM0 TM1 TM2 TM3 TM4 TM5 TM?AUDIO CHANGE SURROUND MUTE WIDE MODE CONTROL ITEM POSITION COMMAND HPOS HPOS V V C C POS POS L L CK CK E E E E E E E E E E E E E E E E V V V V PARAMETER * ? [. . . ]