User manual SHARP LC-52LE8

[. . . ] Under no circumstances should the cut-off plug be inserted elsewhere into a 13A socket outlet, as a serious electric shock may occur. To fit an appropriate plug to the mains lead, follow the instructions below: IMPORTANT: The wires in the mains lead are coloured in accordance with the following code: Blue: Neutral Brown: Live As the colours of the wires in the mains lead of this product may not correspond with the coloured markings identifying the terminals in your plug, proceed as follows: SPECIAL NOTE FOR USERS IN THE U. K. The wire which is coloured blue must be connected to the plug terminal which is marked N or coloured black. The wire which is coloured brown must be connected to the plug terminal which is marked L or coloured red. Ensure that neither the brown nor the blue wire is connected to the earth terminal in your threepin plug. Before replacing the plug cover make sure that: If the new fitted plug contains a fuse, its value is the same as that removed from the cut-off plug. [. . . ] The item marked with * is available only when selecting "HDMI 1", "HDMI 2", "HDMI 3", "HDMI 4" or "EXT 3" from the "INPUT" menu. The item marked with ** is available only when accepting an "x. v. Colour" signal through an HDMI terminal. If you select "AUTO", some selections in the "AV mode" menu may not be automatically set. NOTE Picture Picture AV mode OPC Backlight Contrast OPC Automatically adjusts the brightness of the screen. [Off] Item Off On On:Display The brightness is fixed at the value set in "Backlight". Displays the OPC effect on the screen while adjusting the brightness of the screen. Picture AV mode "AV mode" gives you several viewing options to choose from to best match the system environment, which can vary due to factors like room-brightness, type of programme watched or the type of image input from external equipment. When set to "On", the TV senses the surrounding light and automatically adjusts the backlight brightness. Make sure no object obstructs the OPC sensor, which could affect its ability to sense surrounding light. NOTE Picture You can also switch the mode on the "Picture" and "Audio" menu screen by pressing #. Item Press a/b to select the desired mode, and then press ;. Picture adjustments Adjusts the picture to your preference with the following picture settings. Adjustment items Selectable items Backlight Contrast Brightness Colour Tint Sharpness c (Cursor) The screen dims For less contrast For less brightness For less colour intensity Skin tones become purplish For less sharpness d (Cursor) The screen brightens For more contrast For more brightness For more colour intensity Skin tones become greenish For more sharpness AUTO The TV automatically sets the appropriate selection from the "AV mode" menu depending on the lighting conditions and the type of programme watched. For a clear-cut image emphasising high contrast for sports viewing (the "Picture" and "Audio" settings cannot be adjusted). STANDARD MOVIE GAME PC* USER x. v. Colour** DYNAMIC DYNAMIC (Fixed) Basic adjustment Picture Film mode Automatically detects a film-based source (originally encoded at 24 or 25 frames per second, depending on the vertical frequency), analyses it and then recreates each still film frame for high-definition picture quality ("Advanced (High)", "Advanced (Low)", "Standard", "Off"). Advanced This TV provides various advanced functions for optimising the picture quality. Go to "Menu" > "Setup" > "Picture" > "Advanced". Active contrast Automatically adjusts the contrast of an image according to the scene. C. M. S. -hue This function adjusts the hue of a selected colour using a six-colour adjustment system. DNR "DNR" produces a clearer image ("Auto", "High", "Middle", "Low", "Off"). C. M. S. -saturation This function increases or decreases the saturation of a selected colour using a six-colour adjustment system. NOTE C. M. S. -value This function adjusts the brightness of a selected colour using a six-colour adjustment system. This function may not be available depending on the input signal type. 3D-Y/C Provides high quality images with minimal dot crawl and cross colour noise by detecting changes in the image. Item Standard Fast Slow Normal adjustment. Sets the optimum image quality for slow-moving images. Colour temp. Adjusts the colour temperature to give the best white image. Item High Mid-High Middle Mid-Low Low R/G/B Gain (LO), R/G/B Gain (HI) White with bluish tone. Adjusts the white balance by changing the value of each item. NOTE "3D-Y/C" may not operate depending on the input signal type or when the input signal is noisy. "3D-Y/C" has even more effect on composite video signals (CVBS). Monochrome For viewing a video in black & white. Fine motion advanced "Fine motion advanced" technology provides superior solutions for digital display picture quality removing motion blur ("High", "Low", "Off"). Range of OPC The brightness level range of the OPC sensor's automatic adjustments can be set according to your preferences. The adjustment range of the OPC sensor can be set to a maximum of e 16 and a minimum of f 16. NOTE This effect is greater on fast moving images. You cannot set the Home/Store setting and the country setting in "Auto installation" in the "Setup" menu. If you want to reconfigure those settings, automatically execute initial auto installation after executing "Reset" from the "Setup" menu. The current country setting is displayed on the screen. E Additional search Use this menu to add new services automatically after "Digital search" in the "Auto installation" menu has been completed. E Manual search Add new services within a specified frequency band. Enter the frequency using 0_9 numeric buttons. You can perform "Manual search" with a service number only when the five Nordic countries have been selected in the country setting. 4 Press a/b to select the broadcast standard you want to search, and then press ;. 0 Basic adjustment E Manual adjust Configure various settings for each service using the colour (R/G/B) buttons. Service no. Service name Lock CH skip Old LCN Cable You can reconfigure the following settings when you select "Cable" in the initial auto installation or the "Auto installation" menu. E Additional search Use this menu to add new services automatically after "Digital search" in the "Auto installation" menu has been completed. Follow steps 1 to 5 in Searching for cable broadcasts on page 12. Lock CH skip Delete Sort E Manual search Add new services within a specified frequency band. After setting the items on the following screen, the TV starts searching. Refer to the table about menu items in the right column on page 12. 1 2 Press a/b to select the desired service. Press the colour button on the remote control unit corresponding with the item you want to reconfigure. The 4 mark indicates the operation is set to on. Each time the colour button is pressed, you can switch the corresponding operation on/off. Frequency Symbol rate QAM modulation Search start MHz Buttons for "Manual adjust" operation Lock Press R button. When the service is locked, you must enter your PIN whenever you tune to the service. CH skip Press G button. E Manual adjust This function is the same as in "Terrestrial". Refer to "Manual adjust" in "Terrestrial". Services with a 4 mark are passed over when pressing :r/s on the TV or remote control unit. Delete Press Y button. H You can only reconfigure the "Manual adjust" settings. You can only set the "Lock" setting in "Manual adjust". The selected service is deleted. [. . . ] Acknowledgements The following open source software components are included in this product: linux kernel busy box glibc zlib libpng libjpeg mtd-utils u-Boot Software copyrights BSD License libjpeg Portions copyright 2004 Intel Corporation This product includes software developed by the University of California, Berkeley and its contributors. Portions of this software are based in part on the work of the Independent JPEG Group. Warning regarding basic use Cautions regarding use in high and low temperature environments When the TV is used in a low temperature space (e. g. , room, office), the picture may leave trails or appear slightly delayed. This is not a malfunction, and the TV will recover when the temperature returns to normal. Also, do not leave the TV in a location exposed to direct sunlight or near a heater, as this may cause the cabinet to deform and the LCD panel to malfunction. [. . . ]