User manual SHARP MD-ZV30

[. . . ] S M <P=001> S M <P=001> S M <P=001> S M <P=001> MD STUDIO MD STUDIO MD STUDIO MD STUDIO MODEL MODELL MODÈLE MODELO MD-ZV30H OPERATION MANUAL BEDIENUNGSANLEITUNG MODE D'EMPLOI MANUAL DE MANEJO MD-ZV30H TINSZ0217AWZZ ESPAÑOL FRANÇAIS DEUTSCH ENGLISH SM <P=001> SPECIAL NOTES FOR UK CUSTOMERS ONLY NOTE FOR USERS IN THE U. K. The mains lead of this product is fitted with a non-rewireable (moulded) plug incorporating a 3A fuse. Should the fuse need to be replaced, a BSI or ASTA approved BS 1362 fuse marked or and of the same rating as above, which is also indicated on the pin face of the plug must be used. In the unlikely event of the socket outlet in your home not being compatible with the plug supplied, cut-off the mains plug and fit an appropriate type. Ensure that neither the brown nor the blue wire is connected to the earth terminal in your three pin plug. [. . . ] Adjust it so that the AM broadcast can be tuned in most clearly. 1 1 3 1 6 10 2 7 ST-MODE 3 8 TUNER BAND PROGRAM CLEAR P-MODE REC REC MODE AUTO MARK 4 CD 4 3D SURROUND MODE ON/OFF Press the MD 06 button. 1 1 2 2 3 3 q During recording, you cannot change the station. SLEEP DISPLAY TIME ON/ STAND-BY AUX BASS/ TREBLE To stop recording: Press the MD s button. After the track number has been written on the MiniDisc, the recording will stop. VOLUME To interrupt recording: Press the MD 0 6 button during recording. The track number increases. To record the track number during recording: A recording is performed as a single track. To identify different sections of the recording you can increase the track number at any point during the recording process. To create a new track number, whilst in the record mode, press the REC q button. q The track number will increase by one, and then the recording will continue. q If you press the REC q button and assign a track number, a space of at least 15 seconds should be given between tracks. If the space is shorter than 15 seconds, tracks may not be connected when they are edited. s To record without using One-Touch Editing Without using one-touch recording, the following operation allows you to record from the first track. s To re-record When you want to re-record, you can erase a track that is already recorded, starting from any point in the old track, to begin a new recording. Be aware that when you do this, all of the tracks and track names that follow the newly recorded track will be erased. 1 2 3 4 Press the CD s button. Press the CD button. 1 2 3 4 During playback, press the MD 0 you want to begin re-recording. Press the ENTER button. 6 button at the point where q The unit will pause. Select the recording source and start recording. q The unit will enter the record stand-by mode. 06 To stop recording: Press the MD s button. q After the track number has been written on the MiniDisc, the recording will stop. However, CD playback will continue. E-22 MD-ZV30H TINSZ0217AWZZ <P=003> EDITING We will explain the 5 editing functions with which you can create your own original discs from recorded MiniDiscs. Playback-only MiniDiscs cannot be edited. DIVIDE A track can be divided into two tracks. If two selections were recorded as a single track because there was not enough silent space between the pieces, you can use the DIVIDE function to separate the selections. This feature is also convenient for identifying specific points with one selection so that you can locate those points easily whenever you like. (Page 24) 1 2 3 MOVE The order of the recorded tracks can be changed. (Page 26) 1 2 3 4 A 1 2 B 3 C D 4 1 A 2 B 3 C 4 D A B C D C A B D COMBINE Two adjacent tracks (for example, the third and fourth tracks) can be combined. If there is a prolonged silent section in the middle of a selection that is recorded, a single piece of music may be recorded as two tracks. If this happens, these two tracks can be combined into a single track. (Page 25) 1 2 3 4 Programmed move This function allows the track numbers to be automatically rearranged in the order specified for programmed playback. [. . . ] q No operation q Contact the shop where you purchased the unit. 7 MECHA ERR* q There is a mechanical problem and the disc is not q Turn off the power, and press the (*: Number or symworking properly. bol) NAME FULL NO DISC NOT AUDIO PLAYBACK MD PROTECTED TEMP OVER q The number of characters for the disc name or track q Shorten the disc or track name. q Replace it with a recordable disc. button. q Move the write protection tab back to its original position. (*: Number or symbol) TOC FULL 1 TOC W ERROR TRAY ERROR U TOC ERR* (*: Symbol) U TOC W ERR q There is no space left for recording character information (track names, disc names, etc. ). [. . . ]