User manual SHARP MD-M3H

[. . . ] MD MICRO SYSTEM MODEL OPERATION MANUAL MD-M3H Thank you for purchasing this SHARP product. To obtain the best performance from this product, please read this manual carefully. It will guide you in operating your SHARP product. MD-M3H MD micro system consisting of MD-M3H MD (Main unit) and CP-M3H (Speaker system). CONTENTS Page SPECIAL NOTES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ("Sharp") guarantees to provide for the repair, or at its option the replacement, of this product subject to the conditions listed below:- 1. This guarantee shall only apply to faults which are due to inferior workmanship or materials. [. . . ] q If you tune into a station which is not broadcasting any radio text, even if it is an RDS station, when you switch to the radio text position "NO RT" will be displayed. q Whilst radio text data is being received or when the text contents change, "RT" will be displayed. s To switch the display (Main unit operation) s Notes for RDS operation DISPLAY MODE Each time the DISPLAY MODE button is pressed whilst an FM station is tuned in, the display will switch as follows: Station name (PS) If any of the following events occur, it does not mean that the unit is faulty. q "PS", "NO PS" and a station name appear alternately, and the unit does not operate properly. q If a particular station is not broadcasting properly or a station is conducting tests, the RDS reception function may not work properly. q When you receive an RDS station whose signal is too weak, information like the station name may not be displayed, even if "RDS" is lit. Notes: q "NO PS", "NO PTY" or "NO RT" will flash for about 5 seconds, and then the frequency will be displayed. q The display can only be switched whilst tuned to the FM band. Programme type (PTY) Radio text (RT) Frequency MHz 24 (Continued) s EON-PTY (Main unit operation) 5 When a programme of the type specified starts 4 2 3 on an ON (other network) station, the unit will automatically switch to the station broadcasting the selected programme type, and "PTY" will flash. 6 When the programme specified for the ON station is over, the unit will automatically return to the original station you were tuned to. Note: q If the EON button is pressed when "EON" is not displayed, "NO EON" will appear for 5 seconds to indicate that the unit cannot enter the EON stand-by mode. 1 Tune in the desired RDS station (when a station name is being displayed). Checking the stand-by mode setting: 2 Press the EON button when "EON" appears. When in the EON stand-by mode, press the EON button. ("Programme type" "WAITING") To cancel the EON stand-by mode: When in the EON stand-by mode, press the EON button. ("PTY" will go out. ) q "PTY TI" and "SELECT" will appear alternately for about 6 seconds. About the PTYI (Dynamic PTY Indicator): PTYI (Dynamic PTY Indicator) will appear whilst the Dynamic PTY station is being received. Dynamic PTY indicates that the PTY for the station tuned in, or the PTY referenced in the EON data, is assessed whenever the programme changes and may be changed. Note: q When "PTYI" appears, if you press the DISPLAY MODE button to display the programme type, you can check the type of pro-gramme you are actually receiving. 3 Whilst they are being displayed, select the desired programme type pressing the PRESET (X or W) button. DISC TOC TRACK MEMORY RANDOM TOTAL REMAIN kHz REC MHz SLEEP q The selected programme type will flash. 4 Within 4 seconds, press the PTY. TI SEARCH button. DISC TOC TRACK MEMORY RANDOM TOTAL REMAIN kHz REC MHz SLEEP DISC TOC TRACK MEMORY RANDOM TOTAL REMAIN kHz REC MHz SLEEP q The selected programme type and "WAITING" will be displayed for 2 seconds each. q "PTY" will appear, and the unit will enter the EONPTY stand-by mode. 25 (Continued) s EON-TI (Main unit operation) 5 When a TA specifed starts on a other network station, the unit will automatically switch to that station, and "TI" will flash. 4 2 3 6 When the traffic announcement is over, the unit will automatically return to the original station you were tuned to. Note: q If the EON button is pressed when "EON" is not displayed, "NO EON" will appear for 5 seconds to indicate that the unit cannot enter the EON stand-by mode. 1 Tune in the desired RDS station (when a station name is being displayed). Checking the stand-by mode setting: When in the EON stand-by mode, press the EON button. ("TI" "WAITING") 2 Press the EON button when "EON" appears. To cancel the EON stand-by mode: When in the EON stand-by mode, press the EON button. Note: q If neither "TP" nor "TA" appear, then even if "EON" appears the unit cannot enter the EON-TI standby mode. TI) button is press after TI is selected, "NO TI" will flash for 4 seconds. q "PTY TI" and "SELECT" will appear alternately for about 6 seconds. 3 Whilst they are being displayed, select the TI (Traffic Information) pressing the PRESET (X or W) button. 4 Within 4 seconds, press the PTY. TI SEARCH button. DISC TOC TRACK MEMORY RANDOM TOTAL REMAIN DISC TOC TRACK MEMORY RANDOM TOTAL REMAIN kHz REC MHz SLEEP q "TI" and "WAITING" will appear for 2 seconds each. q "TI" will appear, and the unit will enter the EONTI stand-by mode. 26 (Continued) About the TP and TA indicators TP indicator Not lit Not lit Lit Lit TA indicator Not lit Lit Not lit Lit Meaning This programme does not carry traffic announcements nor does it refer, via EON, to a programme that does. This programme carries EON information about another programme which gives traffic information. This programme carries traffic announcements but none are being broadcast at present and may also carry EON information about other traffic announcements. A traffic announcement is being broadcast on this programme at present. In the following cases, the EON stand-by mode will be cancelled. q When the unit is switched to another band in the EON stand-by mode q When you change the FM station whilst in the EON stand-by mode q When a preset call is made Notes: q During the same programme as the specified PTY (or TA) is being broadcast on the station you are receiving, the unit will not switch to other network station. [. . . ] There is no space left for recording character information(track names, disc names, etc. ). Remedy q Replace it with another disc. q Replace it with another disc. CD NO DISC DISC FULL FOCUS ERR MD ERR MD NO DISC MECHA ERR* (*:Number or symbol) NAME FULL NOT AUDIO PLAYBACK MD PROTECTED READ ERR q Load a CD. q Reload the disc or replace it. TEMP OVER TOC ERR* (*:Number or symbol) TOC FULL* (*:Number or symbol) TOC W ERR U TOC ERR* (*:Symbol) U TOC ERR W q Set this unit to the stand-by mode and wait for a while. q Replace it with another disc. q Replace it with another recordable disc. q Recording is impossible. [. . . ]