User manual SHARP MD-X3H OPERATION MANUAL

[. . . ] Should the fuse need to be replaced, a BSI or ASTA approved BS 1362 fuse marked or and of the same rating as above, which is also indicated on the pin face of the plug must be used. In the unlikely event of the socket outlet in your home not being compatible with the plug supplied, cut-off the mains plug and fit an appropriate type. Ensure that neither the brown nor the blue wire is connected to the earth terminal in your three pin plug. Before replacing the plug cover, make sure that: q If the new fitted plug contains a fuse, its value is the same as that removed from the cut-off plug. [. . . ] q If you press the POLE POSITION button before pressing the CD MD button, a recording can be made from the beginning of the MiniDisc. (Page 30) q If recording does not begin, press the CD MD button again. (See page 26. ) 0 To stop recording: Press the MD s button. s To re-record When you want to re-record, you can erase a track that is already recorded, starting from any point in the old track, to begin a new recording. Be aware that when you do this, all of the tracks and track names that follow the newly recorded track will be erased. 22 1 MD MD 1 1 2 3 4 During playback, press the MD begin re-recording. Press the ENTER button. 0 6 button at the point where you want to q The unit will pause. Select the recording source and start recording. 3 2 4 1 33 MD MD s To record without using One-Touch Editing Without using one-touch recording, the following operation allows you to record from the first track. 1 4 1 2 3 4 Press the CD s button. Press the CD button. q The unit will enter the recording stand-by mode. 06 2 To stop recording: Press the MD s button. q After the track number has been written on the MiniDisc, the recording will stop. However, CD playback will continue. 28 MD-X3HH(SUK) TINSE0227AWZZ <P=004> (Continued) s Recording from the built-in radio onto a MiniDisc MD 4 4 6 MD 6 3 1 2 3 4 Tune in to the desired station. Press the MD q REC button. 25 3 5 To record the track number whilst recording: The recording is performed as a single track. To identify different sections of a recording you can increase the track number at any point during the recording process. Recording from a CD: Press the CD MD TAPE DOLBY NR MD CD CD REVERSE MODE GG 0 TAPE button. 0 TAPE button. Recording from a MiniDisc: Press the MD To stop recording: Press the CD s (MD s) or TAPE s button. 2 s Recording from a CD or an MD to a cassette tape (Synchronised Recording System) When a CD or an MD is played, recording will start automatically. 1 2 3 3 4 5 Load a blank cassette into the cassette compartment. Select the Dolby NR mode by pressing the DOLBY NR button. q Wind past the tape leader which cannot be recorded on. q When recording with the Dolby NR system, turn on the indicator. q When not recording with the Dolby NR system, turn off the indicator. Press the TAPE q 6 button. GG q The unit will enter the recording stand-by mode. Recording from a CD: Press the CD 06 button. Recording from a MiniDisc: Press the MD 06 button. To interrupt recording: Press the CD 0 Press the CD 0 6 6 (MD (MD 0 6) 0 6) button. button again to resume recording. To stop recording: 1 2 Press the CD s (MD s) button, whilst recording. Press the TAPE s button. q The CD or MD will stop, and the unit will enter the stand-by mode. q The tape will stop. 31 MD-X3HH(SUK) TINSE0227AWZZ <P=003> (Continued) s Recording desired tracks from a CD or an MD to a cassette 4 5, 6 3 2 1 4 3 4 2 4 7 7 1 2 3 4 5 6 7 tape (Track Editing) Several consecutive tracks, starting from the first track on a CD or an MD (for example: from the first track to the fourth track), can be recorded onto a tape. Select the Dolby NR mode by pressing the DOLBY NR button. q When recording with the Dolby NR system, turn on the indicator. q When not recording with the Dolby NR system, turn off the indicator. [. . . ] q There is no space left for recording character information (track names, disc names, etc. ). q TOC information recorded on the MD does not match the MD specifications or it cannot be read. q The TOC information could not be created properly due to a mechanical shock or to scratches on the disc. q Music is not being recorded. q Replace it with another recordable disc. q Contact the shop where you purchased the unit. [. . . ]