User manual SHARP MICROWAVE OVEN INSTALLATION INSTRUCTIONS

[. . . ] Use a stud finder, a magnetic device which locates the nails in the stud. Use a hammer to tap lightly across the mounting surface to find a solid sound. The center of the stud can be located by probing the wall with a small nail to find the edges of the stud and then placing a mark halfway between the edges. The center of any adjacent studs will normally be 16" or 24" to either side of this mark. 3/8" Dry Wall or Plaster/lath 16" or 24" 2"x 4" Wood Studs Figure 2 3 ELECTRICAL GROUNDING INSTRUCTIONS This appliance must be grounded. [. . . ] Lift carton off oven and remove all packing materials, Installation Instructions, Wall Template, Top Template, Charcoal Filter, Turntable and Turntable Support; however, DO NOT REMOVE THE WAVEGUIDE COVER, which is located on the ceiling in the oven cavity. Check the oven for any damage, such as misaligned or bent door, damaged door seals and sealing surfaces, broken or loose door hinges and latches and dents inside the cavity or on the door. If there is any damage, do not operate the oven and contact your dealer or SHARP AUTHORIZED SERVICER. If your oven comes with the louver installed, push down carefully on the tabs (B) and (C) at the ends of the louver to disengage it. Loosen the two Mounting Screws (D) which secure the Mounting Plate to the rear side of the oven. See Figure 7. Mounting Plate (A) (B) (C) Mounting Plate (D) (D) Control Panel Side Figure 6 Figure 7 8 VENTILATION SYSTEM This Microwave Oven/Hood is designed for adaptation to three types of hood ventilation systems. Recirculating requires the use of the Charcoal Filter 9 (previously installed or is packed in the packing foam). (A) RECIRCULATING: Non-Vented, Ductless Operation The unit is shipped assembled for recirculating. Attach the Charcoal Filter to the upper side of the oven by sliding into the tabs. The Exhaust Damper Assembly 8 is not required for recirculating operation. The Charcoal Filter should be replaced every 6 to 12 months, depending on use. See page 8 for ordering information. 9 Tabs Tabs Figure 8 4 (B) HORIZONTAL EXHAUST: Outside Ventilation 1. Remove and save 2 screws from back edge and 1 screw from the top center of Fan Cover Bracket. Remove Fan Cover Bracket by sliding it in the opposite direction of the arrow on the Fan Cover Bracket, as shown in Figure 9. Rotate the Hood Fan Unit and turn end-over-end so that the fan blade openings are facing the back of the oven. Be careful not to pinch the lead wire between the inner bracket and the Hood Fan Unit. Replace the Fan Cover Bracket by sliding it into the slits in the same direction as the arrow on the Fan Cover Bracket. Make sure the fan blades are visible through the rear openings in the oven before proceeding. Attach Fan Cover Bracket to unit with 3 screws, which were removed in Step 1 above. Attach the Exhaust Damper Assembly 8 to the back of the Mounting Plate by sliding it into the slits in the same direction as the arrow. Use Tapping Screw 4 X 12 7 from the INSTALLATION HARDWARE and tighten into place. Fan Cover Bracket Back of Oven Figure 9 Figure 10 Figure 11 Figure 12 Wire Box Exhaust Damper Assembly 8 Mounting Plate (Back Side) Tapping Screw 7 Figure 13 5 (C) VERTICAL EXHAUST: Outside Ventilation 1. Remove and save 2 screws from back edge and 1 screw from the top center of the Fan Cover Bracket. [. . . ] Figure 17. Space More Than Wall Thickness Mounting Plate Figure 15 Figure 16 Wall Figure 17 6 MOUNTING OVEN TO THE WALL Two people are recommended to attach the Microwave Oven/Hood to the Mounting Plate. Thread the power supply cord through the hole made in the bottom of the top cabinet. Make sure the unit has been installed according to all of the Installation Instructions, the Top Template and Wall Template. Keep the Installation Instructions for the local electrical inspector's use. ACCESSORIES 1. [. . . ]