User manual SHARP PC-GP22W OPERATION MANUAL

[. . . ] NOTEBOOK COMPUTER PC-GP2 Series OPERATION MANUAL Notice for Users in the USA FCC Statement WARNING - FCC Regulations state that any unauthorized changes or modifications to this equipment not expressly approved by the manufacturer could void the user's authority to operate this equipment. Note: This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. [. . . ] Before using the external monitor, refer to the manual included with the external monitor. 4-3 Switching the Display 1. In the Display Properties dialog box, select Settings tab; then, click Advanced button. · If your options do not appear in the menu, uncheck the box of Auto. · When displaying on the LCD monitor: Set Driver mode to Single and Primary to LCD. · When displaying on the external monitor: Set Driver mode to Single and Primary to VGA. · When displaying on both monitors simultaneously: Set Driver mode to Mirror. · While playing video or animation, you may not be able to switch the display. · When displaying on both of the LCD monitor and the external monitor simultaneously, the external monitor should be capable for displaying in 1024 × 768 resolution or more. Otherwise, you may not display images on the external monitor properly. · To change the resolution and colors, refer to Adjusting the Display of Chapter 2. 4 Displaying the image dividedly on the LCD and an External monitor To display the image separately on the LCD and the external monitor, use the Multimonitor function. Select Multimonitor from Driver mode pull-down menu; click OK, then, Yes. · If your options do not appear in the menu, uncheck the box of Auto. · To exit the Mmultimonitor mode, select Single or Mirror from the Driver mode menu. 4-4 Audio System You can output sound to speakers, audio equipment or a headphone. Connecting Speakers You can connect stereo speakers with an amplifier to the audio output jack on the rear side of the computer. Audio Output Jack Speakers with an Amplifier Stereo Mini Plug 4 Connecting Digital Audio Equipment The audio output jack of the computer is compliant with S/PDIF (Sony/Philips Digital Interface). You can connect a S/PDIF compliant audio equipment to the computer and output/record the sound. Audio Output Jack S/PDIF Compliant Audio Equipment Stereo Mini Plug S/PDIF Compliant Optical Audio Cable When recording sound with an audio equipment: · Use AC adapter for the computer and the digital audio equipment. 4-5 · · · · · Disable Windows power management. Use the digital audio equipment compliant with sampling rate of 48kHz. Sound may not be recorded correctly if you use the synchronized recording system of the digital audio equipment. Connecting Analog Audio Equipment Audio Output Jack White (L) Red(R) 4 Stereo Mini Plug You can adjust the output volume on Windows XP by double-clicking the speaker icon on the taskbar or use Fn + F3 or F4 keys combination. Connecting Headphone Use headphones with an impedance of more than 8 (32 is recommended). Audio Output Jack Stereo Mini Plug 4-6 Connecting a Microphone You can input sound using an external microphone connected to the microphone jack. Use an electret condenser microphone with an impedance of 2. 2k and an allowable voltage of 2. 5V. Microphone Jack Mini Plug To record sound: 1. Click start; then, point All Programs ­ Accessories ­ Entertainment. [. . . ] Confirm the WEP keys are correctly set to your computer if the WEP security of the access point is enabled. Question: Why can't I communicate with other computers through wireless LAN? · · · · · · Confirm the antennas are enabled by pressing Fn+F1 key combination. (Refer to Activate Antennas section of Wireless LAN in Chapter 5. ) Confirm each computer is enabled for wireless LAN. Confirm Computer-to-computer (ad hoc) networks only is selected in Networks to Access of Advanced dialog box of each computer. (To open Advanced dialog box, refer to Communicating with Other Computers section in Chapter 5. ) Adjust the distance between the computers by bringing your computer closer to others and remove any obstructions that may impede the communication; then, try to connect again. [. . . ]