User manual SHARP PG-M20X

[. . . ] Introduction Setup and Connections Basic Operation Easy to Use Functions Appendix OPERATION MANUAL PG-M20X MODEL DIGITAL MULTIMEDIA PROJECTOR IMPORTANT For your assistance in reporting the loss or theft of your Projector, please record the Serial Number located on the bottom of the projector and retain this information. Before recycling the packaging, please be sure that you have checked the contents of the carton thoroughly against the list of "Supplied accessories" on page 14. Model No. : PG-M20X Serial No. : This equipment complies with the requirements of Directives 89/336/EEC and 73/23/EEC as amended by 93/68/ EEC. Dieses Gerät entspricht den Anforderungen der EG-Richtlinien 89/336/EWG und 73/23/EWG mit Änderung 93/ 68/EWG. Ce matériel répond aux exigences contenues dans les directives 89/336/CEE et 73/23/CEE modifiées par la directive 93/68/CEE. [. . . ] I INPUT 1 Mode Main menu Picture Sub menu Contrast Bright Color Tint Sharp Red Blue CLR Temp Reset Signal Type RGB Component 2D Progressive 3D Progressive Film Mode Main menu +30 +30 +30 +30 +30 +30 +30 +3 Options (1) Sub menu Pict in Pict Power Save sRGB [ON/OFF] [ON/OFF] [ON/OFF] -30 -30 -30 -30 -30 -30 -30 -3 Page 40 Page 51 Auto Search [ON/OFF] DNR OFF Level 1 Normal Level A Level B Save Image Delete Sharp Custom Blue None Sharp Custom None Level 3 OSD Display Image Capture Background Progressive Mode Startup Image Fine Sync Clock Phase H-Pos V-Pos Reset Save Setting Select Setting ­150 ­30 ­150 ­60 +150 +30 Auto Power Off [ON/OFF] Page 42 +150 Monitor Out +60 Disable Yes (Y Cable) 1 2 · · Resolution 1024 × 768 800 × 600 Vert Freq Vert Freq 60 Hz 75 Hz 7 Resolution 1024 × 768 800 × 600 Vert Freq Vert Freq 60 Hz 75 Hz Options (2) Lamp Timer Break Timer PRJ Mode Resolution Front Ceiling + Front Rear Ceiling + Rear Normal Level A Level B Old Password New Password Reconfirm Old Code New Code Reconfirm 1 2 · · Page 58 7 Special Modes 1 2 3 7 Signal Info 640 × 480 720 × 480 480p Keylock Level Password Resolution Hor Freq Vert Freq OFF Normal High Speed 640 × 480 31. 5 KHz 60 Hz Anti-Theft Auto Sync Auto Sync Disp [ON/OFF] All Reset Language Page 31 English Deutsch Español Nederlands Français Italiano Svenska Português Status Page 66 Note · The resolution, vertical frequency and horizontal frequency figures displayed above are for example purposes only. · When DVI digital signals have been entered into INPUT 1, in "Picture" only "CLR Temp", "Red" and "Blue" can be adjusted and in "Fine Sync" only "Signal Info", "Auto Sync" and "Auto Sync Disp" can be used. · When the signal type is set as "Component", in the "Picture" menu of INPUT 1 "Color", "Tint" and "Sharp" are displayed. · Some items cannot be reset, even when "All Reset" in Options (2) has been selected. -34 I INPUT 2 / 3 Mode Main menu Picture Sub menu Contrast Bright Color Tint Sharp Red Blue CLR Temp Reset Progressive Mode 2D Progressive 3D Progressive Film Mode ­30 ­30 ­30 ­30 ­30 ­30 ­30 ­3 +30 +30 +30 +30 +30 +30 +30 +3 Main menu Options (2) Sub menu Lamp Timer Break Timer PRJ Mode Front Ceiling + Front Rear Ceiling + Rear Normal Level A Level B Old Password New Password Reconfirm Old Code New Code Reconfirm Page 40 Page 58 Keylock Level Password Anti-Theft All Reset Options (1) Power Save [ON/OFF] Language OFF Level 1 Normal Level A Level B Auto PAL (50/60Hz) SECAM NTSC4. 43 NTSC3. 58 PAL-M PAL-N Sharp Custom Blue None Sharp Custom None [ON/OFF] English Deutsch Español Nederlands Français Italiano Svenska Português Page 52 Auto Search [ON/OFF] DNR OSD Display Page 31 Level 3 Basic Operation Video System Status Page 66 Background Startup Image Auto Power Off -35 Using the Menu Screen This projector has two sets of menu screens that allow you to adjust the image and various projector settings. You can operate the menus from the projector or remote control using the following procedure. On-screen menu for INPUT 2 or INPUT 3 Mode On-screen menu for INPUT 1 RGB mode Menu Bar (Main Menu) Menu Bar (Main Menu) MENU button Basic Operations (Adjustments) buttons 1 Press Note . · The "Picture" menu screen for the selected input mode is displayed. · The on-screen display shown on the right is displayed when the INPUT 1 mode is selected. ENTER button MENU button buttons ENTER button "On-screen Display -36 2 Press or to select the menu you want to adjust. Note · For details on the menus, see the tree charts on pages 34 and 35. 3 Press or to select the item you want to adjust. Note · To display a single adjustment item, press after selecting the item. Then if you press or , the following item ("Phase" is after "Clock") will be displayed. | Basic Operation · Press screen. to return to the previous 4 Press or item selected. to adjust the or the · When you release adjustement is stored. 5 Press . · The on-screen display is cleared. -37 Using the Menu Screen (cont. ) MENU button Basic Operations (Settings) buttons 1 Press Note . · The "Picture" menu screen for the selected input mode is displayed. · The on-screen display shown on the right is displayed when the INPUT 1 mode is selected. ENTER button 2 Press or to select the menu you want to adjust. MENU button Note · For details on the menus, see the tree charts on pages 34 and 35. buttons ENTER button 3 M On-screen Display Press or to select the item you want to set. Note · Press to return to the previous screen. ing " Sub menu -38 4 Press . Sub menu · The cursor shifts to the sub menu. 5 Press or to select the setting of the item displayed in the sub menu. Basic Operation 6 Press . · The item selected is set. Note · Some adjustment items will display a confirmation message. When setting an item, press or to select "Yes" or "OK" and then press . 7 Press . · The menu will disappear. -39 Adjusting the Picture You can adjust the projector's picture to your preferences with the following picture settings. Selected Item Contrast Bright Color Tint Sharp Red Blue CLR Temp Description For adjusting the contrast level For adjusting the brightness of an image For adjusting the color intensity of the image For adjusting the tones of an image button For less contrast For less brightness button For more contrast For more brightness For less color intensity For more color intensity Skin tones become purplish Skin tones become greenish For more sharpness For stronger red For stronger blue Increases color temperature for cooler, bluish, fluorescent-like images. For making sharper or softer the contour of an image For less sharpness For adjusting the redness level For adjusting the blue level For adjusting the color temperature of an image For weaker red For weaker blue Decreases color temperature for warmer, reddish, incandescentlike images. Adjusting Image Preferences Adjust the Picture menu For adjustments, see page 36. Note · "Color", "Tint" and "Sharp" are not displayed when selecting INPUT 1 and the "Signal Type" is "RGB" . · The picture adjustments can be stored separately in each input mode. · When the signal type in INPUT 1 has been set to Component, "Sharp" can be adjusted when 480I, 480P, 720P or 1080I signals are entered. set" and press Selecting the Signal Type This function allows you to select the input signal type RGB or Component for INPUT1. Select "Signal Type" in the "Picture" menu For settings, see page 38. Note RGB Set when RGB signals are received. -40 · Progressive Mode This function allows you to select the progressive display of a video signal. The progressive display projects a smoother video image. Select "Progressive Mode" in the "Picture" menu For settings, see page 38. Note 2D Progressive This function is useful to display fastmoving images such as sports and action films. 3D Progressive · This function is useful to display relatively slow-moving images such as drama and documentary more clearly. This mode optimizes the image by estimating the movement of a number of preceding and succeeding frames. Displays the optimized image of film transformed with three-two pull down (NTSC and PAL60Hz) or two-two pull down (PAL50Hz and SECAM) enhancement to progressive mode images. * The film source is a digital video recording with the original encoded as is at 24 frames/second. The projector can convert this film source to progressive video at 60 frames/second with NTSC and PAL60Hz or at 50 frames/second with PAL50Hz and SECAM to play back a high-definition image. [. . . ] 58 NORMAL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54 Password . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61 PDF . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 Phase . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ]