User manual SHARP SD-CX1

[. . . ] 1-BIT DIGITAL AUDIO SYSTEM SD-CX1H OPERATION MANUAL Special Notes NOTES FOR USERS IN THE U. K. AND IRELAND The mains lead of this product is fitted with a non-rewireable (moulded) plug incorporating a 3A fuse. Should the fuse need to be replaced, a BSI or ASTA approved BS 1362 fuse marked or and of the same rating as above, which is also indicated on the pin face of the plug must be used. Ensure that neither the brown nor the blue wire is connected to the earth terminal in your three pin plug. [. . . ] Press the ENTER button. When an RDS station is found, "RDS" will appear for a short time and the station will be stored in memory. To store a station name again if the wrong name was stored in memory: It may be impossible to store station names in memory using the ASPM function if there is lots of noise or if the signal is too weak. In a certain area or during certain time periods, the station names may temporarily be different. 1 2 After scanning, the number of stations stored in memory will be displayed for 4 seconds, and then "END" will appear for 4 seconds. 30 Web-site: www. sharp. co. uk/support Help Line: 08705 274277 (office hours) To recall stations in memory To specify programme types and select stations (PTY search): You can search a station by specifying the programme type (news, sports, traffic programme, etc. see page 29) from the stations in memory. 1 Press the TUNER (BAND) button to select the FM band. Notes: If the display has stopped flashing, start again from step 2. If the unit finds out a desired programme type, corresponding the station name will flash for 10 seconds and remain lit. If you want to listen to the same programmed type of another station, press the PTY-TI button whilst the channel number and station name are flashing. If no station can be found, "NOT FOUND" will appear for 4 seconds. If you select the traffic programme: If you select the traffic programme (TP) in step 4, "TP" will appear. (This does not mean that you can listen to the traffic information at that time. ) When a traffic information is broadcast, "TA" will appear. "PTY TI" and "SELECT" will appear alternately for about 6 seconds. 3 Within 6 seconds, press the TUN. PRESET the programme type you want. or button to select You can select a station by specifying the name (BBC R1, BBC R2, etc. ) from the stations stored in memory. Before starting this operation, you must store one or more station names in memory. PRESET or button to select the desired station. 3 Each time the button is pressed, the programme type will appear. If the button is held down for more than 0. 5 seconds, the programme type will appear continuously. The station name will be displayed for 3 seconds. Then the display will change as follows. 4 Whilst the selected programme type is flashing (within 4 seconds), press the ENTER button. After the selected programme type has been lit for 2 seconds, "SEARCH" will appear, and the search operation will start. Web-site: www. sharp. co. uk/support Help Line: 08705 274277 (office hours) RDS Radio To specify station names and select stations manually: 31 Using the Radio Data System (RDS) 2 Press the PTY-TI button. Using the Radio Data System (RDS) (continued) To automatically play the desired programme (EON-PTY) When the desired type of programme is broadcast, the radio switches to it automatically. 5 When the specified programme starts on an ON (other network) station, the unit will automatically switch to the station and "PTY" will flash. 1 Tune in to an RDS station (when a station name is displayed). Using the Radio Data System (RDS) 2 6 Press the EON button when "EON" appears. When the programme is over, the unit will automatically return to the original station. RDS Radio Checking the stand-by mode setting: When in the EON stand-by mode, press the EON button. ("Programme type" "WAITING") "PTY TI" and "SELECT" will appear alternately for about 6 seconds. If the EON button is pressed when "EON" is not displayed, "NO EON" will appear for 5 seconds to indicate that the unit cannot enter the EON stand-by mode. To cancel the EON stand-by mode: When in the EON stand-by mode, press the EON button. ("PTY" will go out. ) About the PTYI (Dynamic PTY Indicator): "PTYI" (Dynamic PTY Indicator) will appear whilst the Dynamic PTY station is received. Dynamic PTY indicates that the PTY for the station tuned in, or the PTY referenced in the EON data, is assessed whenever the programme changes and may be changed. Tuned in to a static PTY. 3 Whilst they are displayed, select the desired programme type by pressing the TUN. PRESET or button. The selected programme type will flash. Lights up Goes out 4 Within 4 seconds, press the ENTER button. When "PTYI" appears, press the DISPLAY button to check the type of the current programme. The selected programme type and "WAITING" will be displayed for 2 seconds each. "PTY" will appear, and the unit will enter the EON-PTY stand-by mode. 32 Web-site: www. sharp. co. uk/support Help Line: 08705 274277 (office hours) To automatically play the traffic information (EON-TI) When the traffic information is broadcast, the radio switches to it automatically. 5 When a TA specified starts on an ON (other network) station, the unit will automatically switch to that station, and "TI" will flash. 1 Tune in to an RDS station (when a station name is displayed). 6 2 Press the EON button when "EON" appears. When the traffic announcement is over, the unit will automatically return to the original station you were tuned to. Checking the stand-by mode setting: When in the EON stand-by mode, press the EON button. ("TI" "WAITING") To cancel the EON stand-by mode: When in the EON stand-by mode, press the EON button. ("TI" will go out. ) "PTY TI" and "SELECT" will appear alternately for about 6 seconds. [. . . ] Caution: This operation will erase all data stored in memory including clock, timer settings, tuner preset, and CD or MiniDisc programme. Before transporting the unit Remove the CD and MiniDisc from the unit. "CD NO DISC" and "MD NO DISC" appear if no disc is inside. Carrying the unit with discs left inside can damage it. Condensation Web-site: www. sharp. co. uk/support Help Line: 08705 274277 (office hours) References Sudden temperature changes, storage or operation in an extremely humid environment may cause condensation inside the cabinet (CD pickup, MD pickup, etc. ) or on the transmitter on the remote control. If this happens, leave the power on with no disc in the unit until normal playback is possible (about 1 hour). [. . . ]