User manual SHARP SG-W2CDH

DON'T FORGET : ALWAYS READ THE USER GUIDE BEFORE BUYING !!!

If this document matches the user guide, instructions manual or user manual, feature sets, schematics you are looking for, download it now. Diplodocs provides you a fast and easy access to the user manual SHARP SG-W2CDH. We hope that this SHARP SG-W2CDH user guide will be useful to you.


SHARP SG-W2CDH : Download the complete user guide (641 Ko)

You may also download the following manuals related to this product:

   SHARP SG-W2CDH (682 ko)
   SHARP SG-W2CDH (706 ko)
   SHARP SG-W2CDH (702 ko)
   SHARP SG-W2CDH (706 ko)
   SHARP SG-W2CDH (673 ko)
   SHARP SG-W2CDH (630 ko)
   SHARP SG-W2CDH OPERATION MANUAL (673 ko)
   SHARP SG-W2CDH OPERATION MANUAL (706 ko)

Manual abstract: user guide SHARP SG-W2CDH

Detailed instructions for use are in the User's Guide.

[. . . ] Using this product with a higher voltage other than that which is specified is dangerous and may result in a fire or other type of accident causing damage. SHARP will not be held responsible for any damage resulting from use of this unit with a voltage other than that which is specified. The sound level at a given volume setting depends on speaker efficiency, location and various other factors. It is advisable to avoid exposure to high volume levels, which occurs whilst turning the unit on with the volume control setting up high, or whilst continually listening at high volumes. [. . . ] Repeat steps 1 - 4 to set other stations, or to change a preset station. When a new station is stored in memory, the station previously memorised will be erased. The backup function protects the memorised stations for a few hours should there be a power failure or the AC power lead disconnection. The preset number will flash and the programmed stations will be tuned in sequentially, for 5 seconds each. ) Do not use C-120 tapes or poor-quality tapes, as they may cause malfunctions. Before loading a tape into the cassette compartment, tighten the slack with a pen or pencil. The type of Dolby digital signal being input into this unit can be checked in the display. Normal PCM playback Centre only (monaural) Front (L, R) (When the surround mode is set to Normal or Phantom, sound will also be heard from the surround speakers. ) Front (L, R) + surround (monaural) Front (L, R) + surround (L, R) Front (L, R) + centre Front (L, R) + centre + surround (monaural) Front (L, R) + centre + surround (L, R) If a low frequency sound effect (Low Frequency Effect) contains a Dolby digital signal, "LFE" will light in the display. When this "LFE" is lit, low frequency signals will be output from the subwoofer. ) which is playor trademarks, you can enjoy ing sound sources that have the Dolby surround sound. The sound is output from the subwoofer when in the Bypass/Virtual mode, even if the setting of subwoofer is changed. Within 8 seconds, press the ITEM button to select "CENT" or "SURR". The best sound will be achieved by placing the front speakers, centre speaker and surround speakers at the same distance from the listener. When some of the speakers are at a different distance from the listener, you can select a speaker delay to make it seem as though the speaker distances are the same. (Factory-shipped settings: CENTRE 0 ms, SURROUND 5 ms) If the settings need to be changed due to the type of sound source being played or the conditions in the room, change them as follows. To delay the sound from the centre speaker To delay the sound from the surround speakers Within 8 seconds, use the SET UP (W or X) button on the remote control to select a value. As a guide for setting the correct delay time, 1 ms is equal to approximately 30 cm (12") from where the selected speakers are placed. If the delay time for the surround speakers is set to a large value, a large sound space will be created. If it is set to a small value, the sound space will be small and intimate. You can adjust the balance between the left and right channels of the front speakers. Within 8 seconds, press the ITEM button repeatedly to select the speaker (CENT, RSUR, LSUR or SWFR) you want to adjust. [. . . ] Press the POWER button to enter the stand-by mode, and then unplug the AC power lead from the AC socket. If the TIMER indicator flashes again during use, please unplug the AC power plug, and contact a SHARP authorised service centre. Dirty heads, capstans or pinch rollers can cause poor sound and tape jams. Clean these parts with a cotton swab moistened with commercial head/pinch roller cleaner or isopropyl alcohol. [. . . ]

DISCLAIMER TO DOWNLOAD THE USER GUIDE SHARP SG-W2CDH




Click on "Download the user Manual" at the end of this Contract if you accept its terms, the downloading of the manual SHARP SG-W2CDH will begin.

 

Copyright © 2015 - manualRetreiver - All Rights Reserved.
Designated trademarks and brands are the property of their respective owners.