User manual SHARP SYSTEM-S400H

[. . . ] Micro sistemi SYSTEM-S400H composto da SYSTEM-S400H (apparecchio principale) e CP-HP700H (sistema di diffusori). SYSTEM-S400H micro systeem bestaande uit SYSTEM-S400H (hoofdtoestel) en CPHP700H (luidsprekersysteem). SYSTEM-S400H Sistema de Micro Componente composto de SYSTEM-S400H (unidade principal) e CP-HP700H (sistema de alto-falante). SYSTEM-S400H Micro Component System consisting of SYSTEM-S400H (main unit) and CP-HP700H (speaker system). SYSTEM-S400H BEDIENUNGSANLEITUNG MODE D'EMPLOI MANUAL DE MANEJO BRUKSANVISNING MANUALE DI ISTRUZIONI GEBRUIKSAANWIJZING MANUAL DE OPERAO OPERATION MANUAL DEUTSCH FRANAIS ESPAOL SVENSKA ITALIANO NEDERLANDS PORTUGUS ENGLISH Siehe Seiten i bis vi und D-1 bis D-32. [. . . ] " Periodically clean the transmitter on the remote control and the sensor on the unit with a soft cloth. " Exposing the sensor on the unit to strong light may interfere with operation. " Keep the remote control away from moisture, heat, shock, and vibrations. SYSTEM-S400H ENGLISH 3 !Test of the remote control Precautions for battery use: " Replace all old batteries with new ones at the same time. " Remove the batteries if the unit is not to be used for long periods of time. Caution: " Do not use rechargeable batteries (nickel-cadmium battery, etc. ). " Installing the batteries incorrectly may cause the unit to malfunction. The remote control can be used within the range shown below: Press the ON/STAND-BY button. Now, you can enjoy music. Remote sensor 0. 2 m - 6 m (8" - 20') Preparation for Use Check the remote control after checking all connections have been made correctly. (See pages 7 - 8. ) Point the remote control directly at the remote sensor on the unit. 8 E-6 02/7/22 SYSTEM-S400H(H)E1. fm SYSTEM-S400H System connections !Aerial connection AM loop aerial FM aerial ENGLISH Supplied FM aerial: Connect the FM aerial wire to the FM 75 OHMS socket and position the FM aerial wire in the direction where the strongest signal can be received. Left speaker Right speaker Supplied AM loop aerial: Connect the AM loop aerial to the AM LOOP socket. Place the AM loop aerial on a shelf, etc. , or attach it to a stand or a wall with screws (not supplied). Remote control operation: Press the VOLUME (+ or -) button to increase or decrease the volume. ROCK CLASSIC Treble is cut a little. 29 30 MAXIMUM E-9 02/7/22 SYSTEM-S400H(H)E1. fm Setting the clock 4 Press the TUNING/TIME ( or ) button to adjust the hour and then press the MEMORY/SET button. SYSTEM-S400H ENGLISH " Press the TUNING/TIME ( or ) button once to advance the time by 1 hour. " When the 12-hour display is selected, "AM" will change automatically to "PM". The clock should be set on the main unit. In this example, the clock is set for the 24-hour (0:00) display. 5 Press the TUNING/TIME ( or ) button to adjust the minutes and then press the MEMORY/SET button. Press the CLOCK button on the main unit and within 5 seconds, press the MEMORY/SET button. 3 Press the TUNING/TIME ( or ) button to select 24-hour or 12-hour display and then press the MEMORY/SET button. " Press the TUNING/TIME ( or ) button once to advance the time by 1 minute. " The hour will not advance even if minutes advance from "59" to "00". "0:00" The 24-hour display will appear. (AM 12:00 - PM 11:59) "AM 0:00" The 12-hour display will appear. (AM 0:00 - PM 11:59) Note that this can only be set when the unit is first installed or it has been reset. [Refer to "Clearing all the memory (reset)" on page 30 for details. ] To confirm the time display: Press the CLOCK button on the main unit or remote control. Note: The "CLOCK" or time will flash at the push of the CLOCK button when the AC power supply is restored after a power failure or unplugging the unit. To readjust the clock: Perform "Setting the clock" from step 1. If the time display is flashing, step 3 (for selecting the 24-hour or 12-hour display) will be skipped. [. . . ] Adjust the volume using the VOLUME control. Advanced Features 8 E-28 02/7/22 SYSTEM-S400H(H)E3. fm SYSTEM-S400H Troubleshooting chart Many potential problems can be resolved by the owner without calling a service technician. If something is wrong with this product, check the following before calling your authorised SHARP dealer or service centre. ENGLISH " Tuner Symptom !Move the aerial away from the AC power lead or the unit if located near. " General Symptom !(Refer to page 10. ) Set this unit to the power standby mode and then turn it back on. [. . . ]