User manual SHARP UX-300

[. . . ] Troubleshooting WARNING FCC Regulations state that any unauthorized changes or modifications to this equipment not expressly approved by the manufacturer could void the user's authority to operate this equipment. Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. [. . . ] The display will show: READY TO SEND 2 Press the START/MEMORY key and then 2. START/MEMORY 2 3 Dial the receiving machines (maximum of 20) using one or both of the following methods: · Enter one or more Speed Dial 01 2 02 2 03 numbers by pressing the number keys. · Press one or more Rapid Keys. (Example) 4 Press the START/MEMORY key. START/MEMORY · Set the resolution and/or contrast if RESOLUTION desired. 72 Broadcasting 5 Press the START/MEMORY key. Transmission will begin. · A Transaction Report is automatically printed out after Broadcasting is completed. Check the "Note" column of the report to see if any of the locations are marked "Busy" or have a communication error code. If so, send the document to those locations again. START/MEMORY 73 7. Special Functions Cover Sheet Cover Sheet You can have the fax generate a cover sheet and send it as the last page of each of your fax transmissions. You can select a message. For the recipient's name to appear, you must dial using a Speed Dial or Rapid Key number with the name programmed. Your name and number must be programmed as explained in Chapter 1. Follow the steps below to turn on the cover sheet function. Once the cover sheet function is turned on, cover sheets will be included with all tranmissions until you turn it off. 1 Press these keys: The display will show: OPTION SETTING FUNCTION 4 2 Press these keys: The display will show: COVER SHEET 74 Cover Sheet 3 Press 1 (YES) to turn on the cover sheet function, or 2 (NO) to turn it off. The display will show: AUTO PRINT OUT YES NO or 1 2 4 Press the STOP key to return to the date and time display. STOP Selecting a header message (optional) When the cover sheet function is turned on, you can also select a message which will appear as a header at the top of the cover sheet. Note that the message selection is only effective for one transmission. 1 Load the document(s). · The document must be loaded before a message can be selected. · The cover sheet function must be turned on. FUNCTION The display will show: COVER SHEET HEAD 5 75 7. Special Functions 2 Press these keys: Cover Sheet 3 Select a message by entering a number from 1 to 4: 1: URGENT 2: IMPORTANT 3: CONFIDENTIAL 4: PLS. DISTRIBUTE 1 (Example) 4 Dial the receiving machine and transmit the document. Note: To cancel a cover sheet header setting, press the STOP key or remove the document from the feeder. 76 Batch Page Numbering Batch Page Numbering You can change the page numbering of the transmitted document from simple numbering ("P. 01", "P. 02", etc. ) to batch numbering, which means that a slash and the total number of pages being sent are added after each page number (for example, "P. This allows the receiver to check for missing pages. 1 Load the document(s). · The document must be loaded before batch page numbering can be set. 2 Press these keys: The display will show: PAGE COUNTER SET FUNCTION 3 Enter the total number of pages ("01" to "99") by pressing the number keys. · If you are sending a cover sheet, do 0 8 Example: Eight pages 7. Special Functions not include it in the total number of pages (the number will be adjusted automatically). 4 Dial the receiving machine and transmit the document. 77 Batch Page Numbering Comments: · If you need to cancel a batch number entry, remove the document from the feeder or press the STOP key. · If the number of pages actually transmitted does not coincide with the batch number entered, the alarm will sound and PAGE COUNT ERROR will appear in the display. will also appear in the NOTE column of the Transaction Report if it has been set to print out. 78 Blocking Reception of Unwanted Faxes Blocking Reception of Unwanted Faxes The Anti Junk Fax function allows you to block reception of faxes from parties which you specify. To use this function, first turn it on by setting Option Setting 13 to YES as explained in Chapter 8, and then enter the fax numbers from which you do not want to receive faxes as shown below. If you are using the Caller ID function, you can also enter voice numbers. Comments: · Up to 5 numbers can be entered in the Anti Junk Number List. · The Anti Junk function will not operate for a number which has also been stored as a Priority Call number. · To clear a number from the Anti Junk Number List, you need to know the 1-digit number which identifies it. If you have forgotten this number, print out the Anti Junk Number List as explained in Chapter 9. 1 Press the keys shown at right. Press 1 to store a number in the Anti Junk Number List, or 2 to clear a number from the list. FUNCTION 3 2 SET CLEAR or 1 2 3 Storing: Enter a 1-digit number from 1 to 5. This number identifies the fax/voice number you will store in the next step. Clearing: Enter the number which identifies the fax/voice number you want to clear, and go to Step 5. 1 (Example) 79 7. Special Functions Blocking Reception of Unwanted Faxes 4 Enter the full number you want to block (max. [. . . ] Precautions for Safe Handling and Use Personal Protection Information (Respiratory, Engineering Control/Ventilation: Work/Hygienic Practice: Steps to be taken in case of Spill or Leak: Eye Protection and Protective Glove): not required not required none If rumple the product and wax layer peel off, sweep up or clean with vacuum cleaner. Dispose in an approved incinerator or contract with licensed chemical disposal agency. (Dispose by the same method of ordinary plastic products. ) Waste Disposal Method: Section 10. Regulatory Information NFPA Rating (U. S. A. ): WHMIS Legislation (Canada): Transport Information: UN No. : no information not controlled no information no information Section 11. [. . . ]