User manual SHARP UX-P115

[. . . ] Troubleshooting WARNING - FCC Regulations state that any unauthorized changes or modifications to this equipment not expressly approved by the manufacturer could void the user's authority to operate this equipment. Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. [. . . ] To change the setting, follow the steps below. 1 2 3 4 Press FUNCTION once and once. Display: OPTION SETTING Press once and once. COPY CUT-OFF Press once. 1=YES, 2=NO Press 1 to set copy cut-off to YES (the remaining part of the document will not be printed), or 2 to set copy cut-off to NO (the remaining part will be printed on a second page). The display briefly shows your selection, then: NUMBER OF RING 5 Press STOP to return to the date and time display. 48 5. Special Functions Caller ID (Requires Subscription to Service) If you subscribe to a caller identification service from your telephone company, you can set your fax machine to display the name and number of the caller while the fax rings. Important: To use this function, you must subscribe to a caller identification service from your telephone company. Note that the machine may not be compatible with some caller identification services. Area Code mode: This step is needed if your telephone exchange cannot dial a local phone number (within your calling area code) when the area code is dialed with the phone number (see Step 5). 1 2 3 4 Press FUNCTION once and once. Display: OPTION SETTING Press once and 5 times. CALLER-ID Press once. 1=YES, 2=NO Press 1 (YES) to turn on Caller ID. and go AREA CODE # MODE (To turn off Caller ID, press 2 to Step 8. ) 1=SET, 2=CLEAR 5 Press 1 to select SET. (To clear a previously set area code, press ENTER AREA CODE 2 and go to Step 8. ) Note: Entering your area code in this step causes it to be automatically removed from local numbers in the Caller ID list (page 51). This is only required if you need to eliminate dialing of the area code when dialing a local number from the list. Example (using the area code "123"): If Step 5 is skipped, the Caller ID display will show 123-444-1234, and the number that will dial from the Caller ID list is 123444-1234. If the area code 123 is entered in Step 5, the Caller ID display will show 444-1234, and the number that will dial from the Caller ID list is 444-1234. 49 5. Special Functions Caller ID (Requires Subscription to Service) 6 7 8 Enter the three digits of your area code. Press START/MEMORY to store your area code. DAY LIGHT SAVE Press STOP to return to the date and time display. How Caller ID operates When you receive a call, the name and phone number of the caller will alternately appear in the display, beginning just before the second ring. The information will continue to be displayed until the line is disconnected. Note: Some caller ID services may not provide the name of the caller. In this case, only the phone number will appear. Display example JOHN DOE 525-8693 Caller's name Caller's number Display messages One of the following messages will appear while the fax rings if caller information is not available. NO SERVICE No caller information was received from your telephone company. Make sure that the telephone company has activated your service. CALLER-ID ERROR Noise on the telephone line prevented reception of caller information. OUT OF AREA The call was made from an area which does not have a caller identification service, or the caller's service is not compatible with that of your local phone company. Caller information was not provided by the telephone company at the caller's request. PRIVATE CALL 50 Caller ID (Requires Subscription to Service) Viewing the Caller ID list If you subscribe to a Caller ID service and have turned on the Caller ID function, your fax machine will keep information on the most recent 30 calls and faxes you have received. You can view this information, which consists of the name and number of each caller, in the Caller ID List. After you have received 30 calls, each new call will delete the oldest call. All calls will be erased if you unplug the fax or a power failure occurs. Follow the steps below to view the Caller ID List in the display. If desired, you can immediately dial a number when it appears. 1 2 3 Press twice. <REVIEW CALLS> Press or to scroll through the list. If you want to dial one of the numbers in the list, scroll through the list until the number appears in the display. · Fax: If you want to send a fax, load the document and then press START/MEMORY . START/MEMORY Dialing and transmission begin. Fax: · Voice call: If you want to make a voice call, pick up the handset (or press SPEAKER ). Dialing begins automatically. SPEAKER (If you pressed , pick up the Voice call: handset when the other party answers. ) 4 Press STOP when you have finished viewing the list. 51 5. Special Functions Caller ID (Requires Subscription to Service) To delete calls from the Caller ID list If you want to delete a single call from the caller list, press while the call appears in the display. [. . . ] 4. Pulse START/MEMORY . . Programación de números de marcación automática 1. Pulse FUNCTION Marcación abreviada 1. Pulse SPEED una vez y una vez. . 2. Introduzca un número de 2 dígitos de Marcación abreviada (01 a 30). Introduzca el número de telefax y pulse START/MEMORY 2. Introduzca el número de 2 dígitos de marcación abreviada. [. . . ]