User manual SHARP VC-M31GM/M51GM

DON'T FORGET : ALWAYS READ THE USER GUIDE BEFORE BUYING !!!

If this document matches the user guide, instructions manual or user manual, feature sets, schematics you are looking for, download it now. Diplodocs provides you a fast and easy access to the user manual SHARP VC-M31GM/M51GM. We hope that this SHARP VC-M31GM/M51GM user guide will be useful to you.


SHARP VC-M31GM/M51GM : Download the complete user guide (2288 Ko)

You may also download the following manuals related to this product:

   SHARP VC-M31GM/M51GM (2193 ko)

Manual abstract: user guide SHARP VC-M31GM/M51GM

Detailed instructions for use are in the User's Guide.

[. . . ] Please refer to the relevant laws in your country. G No part of this publication may be reproduced, stored or transmitted in any form without prior permission from SHARP Electronics (Europe) GmbH. ® and PlusCode ® are registered trademarks of Gemstar Development G Corporation. G system is manufactured under license from Gemstar Development Corporation. SAFETY WARNINGS Observe all warnings for your safety and to ensure trouble free use of your VCR. INFORMATION Additional information complements instructions. (i) VCR REMOTE CONTROL 14. RECORD (The STOP button is also used to switch on the VCR. ) / 1. TIMER ON/OFF 5. AUDIO OUT (This button has no function with the VC-M303LM) / 6. If you prefer, or if remote control batteries fail, you will need to use the VCR front panel controls. [. . . ] When the correct date for your recording is shown, press the menu select button to move to the next setting. SET : SE L ECT : ENT ER ME NU : E X I T 1/2 DA T E 21 / 06 9 / 07 --/---/-P R S T AR T S T OP 02 12 : 00 13 : 00 --:--:---:--:---:--:-SP ---- 5. If you want to make additional recordings at the same time each day or week, use [ / ] to select D (daily) or W (weekly). Then press to move to the next setting. 1/2 DA T E P R S T AR T S T OP 21 / 06 02 12 : 00 13 : 00 9 / 0 7D - -:--:---/-- --:--:---/-- --:--:-SP ---- 6. Then press to move to the next setting. If problems persist contact the SHARP Helpline on tel: 0990-274277 16 BASIC OPERATION HOW TO SET A DELAYED RECORDING 7. Enter the start time using the [ / ] or the 1/2 DA T E P R S T AR T S T OP 21 / 06 02 12 : 00 13 : 00 9 / 0 7D0 3 2 1 : 0 5 -:---/-- --:--:---/-- --:--:-SP SP --- NUMBER BUTTONS, hours first then minutes (when entering less than 10 hours or minutes add a '0' before the number), for example for 21:05 start, press 2 1 0 5. Enter the stop time, for example for 22:30 stop, press 2 2 3 0. 9. If your VCR has long play facility and you wish to change the RECORDING SPEED, use the [ / ] to highlight SP. Press [ / ] to select standard play (SP) or long play (LP) as required. 1/2 DA T E P R S T AR T S T OP 21 / 06 02 12 : 00 13 : 00 9 / 0 7D0 3 2 1 : 0 5 2 3 : 0 0 --/-- --:--:---/-- --:--:-SP LP --- 10. Press SET to confirm. · The MENU now shows all the timer settings you have entered. If you wish to make additional timer recordings, repeat this procedure. Ensure that the tape on which you wish to record is inserted into the VCR, then press TIMER ON/OFF once to place the VCR in TIMER STANDBY mode. When connected in this way stereo sound is possible from the speakers. EXISTING AERIAL CABLE BACK OF TELEVISION RF CONNECTION CABLE ANTENNA IN ENTREE RF OUT SORTIE ANTENNE AERIAL IN RF-OUT AUDIO OUT L and R AUDIO PHONO LEADS (NOT SUPPLIED) + AMPLIFIER If problems persist contact the SHARP Helpline on tel: 0990-274277 20 ADVANCED OPERATION PLAYBACK OF A VIDEO TAPE CHECKING THE AMOUNT OF TAPE REMAINING When you load a video tape into the VCR it can calculate approximately the amount of video tape remaining in hours and minutes. This is useful in determining whether or not there is sufficient tape left to make a recording. When a video tape is playing, the amount of tape remaining is calculated for you automatically. Press DISPLAY on the remote control as many times as necessary until "R" appears on the VCR display. The tape remaining will be shown on the VCR display in hours and minutes. By pressing the TAPE SPEED button on the remote control the remaining time will change between long play and standard play. For example, in standard play 1 hour 23 minutes is left on the tape: Pr in long play 2 hour 46 minutes is left on the tape: Pr NOTES: · · If tape remaining function is interrupted, the remaining time will not be displayed. If less than 5 minutes of tape remains the display will flash. PLAYING BACK A VIDEO TAPE REPEATEDLY You can set your VCR to automatically rewind at the end of playing a video tape and replay the entire tape again. Press MENU to display the main menu on the screen. MODE MENU SCREEN B L U E MU T E R E P E A T AU T O ON OF F OF F 2. Press [ Press [ / ]menu select buttons to ]to select REPEAT. / Press SET. ]to select ON. SET : SE L ECT : ENT ER : CHANGE ME NU : E X I T 7. Press MENU to return to normal screen. If problems persist contact the SHARP Helpline on tel: 0990-274277 21 ADVANCED OPERATION DIGITAL DISPLAY TIME OF DAY Shows current time of day, if the clock is set. [. . . ] (hereafter called Sharp) guarantee to provide for the repair, or at its option the replacement, of this product subject to the conditions listed below: 1. This guarantee shall only apply to faults which are due to inferior workmanship or materials. It does not cover faults or damage by accident, misuse, fair wear and tear, neglect, tampering with the product, or repair other than by a Service Facility appointed by SHARP. 2. As this product is intended for private domestic use only, the guarantee will not apply if the product is used in the course of a business, trade or profession. 3. [. . . ]

DISCLAIMER TO DOWNLOAD THE USER GUIDE SHARP VC-M31GM/M51GM




Click on "Download the user Manual" at the end of this Contract if you accept its terms, the downloading of the manual SHARP VC-M31GM/M51GM will begin.

 

Copyright © 2015 - manualRetreiver - All Rights Reserved.
Designated trademarks and brands are the property of their respective owners.