User manual SHARP VCMH85 OPERATION MANUAL: CONTENTS & BODY

[. . . ] TINS-A101UMZZ. book Page 1 Thursday, July 25, 2002 2:49 PM CONTENTS BEFORE USING YOUR VCR Important notes on your VCR . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Unpacking the accessories. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 INSTALLING YOUR VCR Connecting the cables . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Auto Tuning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] Ensure that the tape on which you wish to record is inserted into the VCR, then press the TIMER ON/OFF button once to place the VCR in TIMER STANDBY mode. NOTES: · · If the symbol flashes a video tape has not been inserted into the VCR. If the video tape is ejected when the VCR tries to record the record protection tab has been removed. If there are further recordings to be made, the VCR will return to Timer Standby. www. sharp. co. uk/support 16 TINS-A101UMZZ. book Page 17 Thursday, July 25, 2002 2:49 PM BASIC OPERATION HOW TO CHECK, CHANGE AND CANCEL A DELAYED RECORDING Before you start! · If the Timer Standby symbol press the TIMER ON/OFF symbol. appears on the VCR display, button to remove the CHECKING A RECORDING 1. Press the SET · SET MENU SCREEN T I ME R MOD E SE T UP button to confirm. All the delayed recordings in the VCR's memory will be shown. If the settings are correct press the MENU SET ME NU : E X I T · If you wish to change or cancel any settings, follow the procedures below. CHANGING A RECORDING 1. To change a delayed recording, press [ / ] to highlight the recording, then press SET the SET button to select. 3. Press[ / ]to highlight the setting to be / ] 1/2 DA T E 21 / 06 --/---/---/-P R S T AR T S T OP 02 12 : 00 13 : 00 --:--:---:--:---:--:-SP ---- changed and correct it by using the[ or the NUMBER BUTTONS. SET 4. When all corrections are complete press the SET button to confirm, then press the MENU button to exit. To cancel a delayed recording, press [ / ]to highlight the recording to be cancelled, then press CLEAR. 1/2 DA T E P R S T AR T S T OP 2 1 / 0 6 0 2 1 2 : 0 0 1 3 : 0 0 SP --/-- --:--:-- ---/-- --:--:-- ---/-- --:--:-- -- 3. Press the MENU NOTE: · button to exit. If there are some programmes to be recorded, do not forget to press TIMER ON/OFF button to return the VCR to Timer Standby mode. www. sharp. co. uk/support 17 TINS-A101UMZZ. book Page 18 Thursday, July 25, 2002 2:49 PM ADVANCED OPERATION AUDIO AND YOUR VCR HI-FI STEREO SOUND Stereo sound is possible from this VCR if you have a stereo TV connected to the VCR with a scart lead, or audio equipment connected with audio phono leads. The sound output from the VCR is controlled by the AUDIO OUT button on the remote control. If you wish to change the sound output you can use the AUDIO OUT button as follows: · button once. The LEFT audio channel will be sent to BOTH Press the AUDIO OUT speakers. Press the AUDIO OUT button a third time and the MONO track will be sent to BOTH speakers. Pressing the AUDIO OUT button a fourth time, normal Hi-Fi stereo sound will be heard. L and R will appear on the VCR display. · · · NICAM Hi-Fi STEREO SOUND Your VCR can receive and record NICAM sound. The VCR is normally set so that NICAM sound is possible if it is present on the receiving signal, otherwise the VCR will automatically switch to receive the mono signal. Press the [ button to display the main menu on the screen. / ] menu select buttons to SET select MODE then press theSET button to confirm. The MODE menu will be displayed with NICAM selected. N I CAM CO L OUR AU T O AU T O OF F PAL · 3. [. . . ] The channel number can now be changed by using the MENU SELECT buttons. (The screen opposite should be displayed on the TV) SET V CR R F 6. (White text blue background) SET : ENT ER ME NU : E X I T RF THROUGH ON/OFF: If you wish to connect your VCR to the TV with only a scart lead, the RF Output on your VCR can be turned OFF and ON. To do this press the CLEAR then SET SET buttons on the remote control at point 3 from RF CHANNEL TUNING above. [. . . ]