User manual SHARP XV-Z10E

[. . . ] XV-Z10E PROJECTOR PROJEKTOR PROJECTEUR PROJEKTOR PROYECTOR PROIETTORE PROJECTOR OPERATION MANUAL BEDIENUNGSANLEITUNG MODE D'EMPLOI BRUKSANVISNING MANUAL DE MANEJO MANUALE DI ISTRUZIONI GEBRUIKSAANWIJZING ENGLISH . . . . . . . . . . . . . NEDERLANDS . . . . -1 ­ -1 ­ -1 ­ -1 ­ -1 ­ -1 ­ -1 ­ -68 -68 -68 -68 -68 -68 -68 This equipment complies with the requirements of Directive 89/336/EEC and 73/23/EEC as amended by 93/68/EEC. Dieses Gerät entspricht den Anforderungen der EG-Richtlinien 89/336/EWG und 73/23/EWG mit Änderung 93/68/EWG. Ce matériel répond aux exigences contenues dans les directives 89/336/CEE et 73/23/CEE modifiées par la directive 93/68/CEE. [. . . ] Used for projecting images from equipment connected to the INPUT 3 terminal. INPUT 3 mode Using Video Using RGB INPUT 2 mode Using S-Video Basic Operation Volume buttons Adjusting the Volume Press or on the remote control to adjust the volume. Note · Pressing will lower the volume. · On the projector, the volume can be adjusted by pressing or . Volume buttons "On-screen Display -27 Image Projection Turning off the Sound Temporarily Press on the remote control to temporarily turn off the sound. Note · Pressing on. again will turn the sound back "On-screen Display MUTE button Turning the Power off (Putting STANDBY button the Projector into the Standby Mode) 1 Press on the projector or on the remote control, then press that button again while the confirmation message is displayed, to put the projector into the standby mode. "On-screen Display Note · If you accidentally pressed or and do not want to put the projector into the standby mode, wait until the confirmation message disappears. 2 Unplug the power cord from the wall outlet after the cooling fan stops. Info · Do not unplug the power cord during projection or cooling fan operation. The cooling fan in this projector continues to run for about 90 seconds after the projector enters the standby mode. This can cause damage due to rise in internal temperature, as the cooling fan also stops. -28 Correcting Trapezoidal Distortion When the image is projected either from the top or from the bottom towards the screen at an angle, the image becomes distorted trapezoidally. The function for correcting trapezoidal distortion is called Keystone Correction. ', ", \, | buttons KEYSTONE button UNDO button Note · The Keystone Correction can be adjusted up to an angle of approximately ±30 degrees and the screen can also be set up to an angle of approximately ±30 degrees (when the resize mode is set to "STRETCH" for the video signal input or "SIDE BAR" for the computer signal input). · The Keystone Correction cannot be adjusted in the lateral direction. · For details about the setup, see pages 7 and 16. UNDO button ', ", \, | buttons "On-screen display (Keystone Correction mode) 1 Basic Operation Press to enter the Keystone Correction mode. · The on-screen display of the Keystone Correction mode will appear. Compresses upper side. 2 Press ', ", \ and | to adjust the Keystone Correction. · You can also adjust the Keystone Correction using the , tons on the projector. · Straight lines or the edges of images may appear jagged while adjusting the image. · When correcting trapezoidal distortion, the aspect ratio of the image will change slightly . Compresses lower side. 3 Press . · The on-screen display of the Keystone Correction mode will disappear. -29 Image Projection Adjusting the Lens The image is focused and adjusted to the desired size using the focus ring or zoom knob on the projector. Zoom knob Focus ring 1 Adjust the focus by rotating the focus ring. 2 Adjust zooming by moving the zoom knob. Zoo m in Zoo mo ut -30 Using the Adjustment Feet The height of the projector can be adjusted using the adjustment feet at the front and rear of the projector when the screen is not perpendicular to the lens centre of the projector, or when installation surface is slightly slanted. When the screen is in a higher position than the projector, the projection image can be made higher by adjusting the projector. HEIGHT ADJUST button 1 2 Press the HEIGHT ADJUST button. · The front adjustment foot comes out. Lift the projector to adjust its height while pressing the HEIGHT ADJUST button. · The projector is adjustable up to approximately 12 degrees (5 steps). · When lowering the projector, it may be difficult to move the front adjustment foot because the installation surface is difficult to slide. HEIGHT ADJUST button Front adjustment foot Basic Operation 3 Remove your hands from the HEIGHT ADJUST button of the projector after its height has been finely adjusted. Use the rear adjustment foot to make the projector level. · The projector is adjustable ±1 degree from the standard position. 4 Note · When the height of the image is being adjusted by the adjustment feet, the image becomes distorted trapezoidally. In this case, see "Correcting Trapezoidal Distortion" on page 29 to correct the trapezoidal distortion. Info · Do not press the HEIGHT ADJUST button when the front adjustment foot comes out without firmly holding the projector. · When lowering the projector, be careful not to get your fingers caught in the area between the adjustment foot and the projector. Rear adjustment foot -31 Image Projection Variable Lens Shift Feature In addition to the zoom function and adjustment of projection angle using the adjustment foot, it is possible to move the lens up and down and left and right (360°) to adjust the projection position simply by moving the lens shift lever on the front of the projector. This is a useful function in cases such as when the screen cannot be moved. When moving upwards or downwards When moving in the left and right direction ge Adjustable ran Adjustable range ge Adjustable ran Adjustable range Lens shift lever Adjustable range of the lens shift lever The adjustable range using the lens shift lever has limitations. The image can be adjusted as shown below. Lens shift lever Image centre locus Zooming axis Adjustable range of the image centre Image centre Height of the projected image × (about) 60% Width of the projected image × (about) 30% -32 Adjusting the Projected Image Position Adjust the projected image position using the lens shift lever. Info · When using the projector (during projection), be sure not to subject the projector to any impact. If the projector is subjected to impact, the projection image may deviate from the adjusted position. · When transporting or carrying the projector, attach the lens shipping block and the lens cap to the projector. [. . . ] 47 OSD Display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47 Phase . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42 Picture Setting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44 Power cord . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ]