User manual SHIMANO SI-0071A TECHNICAL INSTRUCTIONS
DON'T FORGET : ALWAYS READ THE USER GUIDE BEFORE BUYING !!!
If this document matches the user guide, instructions manual or user manual, feature sets, schematics you are looking for, download it now. Diplodocs provides you a fast and easy access to the user manual SHIMANO SI-0071A. We hope that this SHIMANO SI-0071A user guide will be useful to you.
You may also download the following manuals related to this product:
SHIMANO SI-0071A MONTAGE (195 ko)
SHIMANO SI-0071A TECHNICAL INSTRUCTIONS (806 ko)
SHIMANO SI-0071A TECHNICAL INSTRUCTIONS (195 ko)
Manual abstract: user guide SHIMANO SI-0071ATECHNICAL INSTRUCTIONS
Detailed instructions for use are in the User's Guide.
[. . . ] SI-0071A-002-00
General Safety Information
WARNING
To avoid serious injuries:
Technical Service Instructions
3. While holding the shoe against the rim, tighten the shoe
SI-0071A-002
fixing nut.
· Improper use of your bicycle's brake system may result in a loss of control or an accident, which could lead to a severe injury. [. . . ] · Always make sure that the front and rear brakes are working correctly before you ride the bicycle. · The required braking distance will be longer during wet weather. To avoid this, reduce your speed and apply the brakes early and gently. · Read these Technical Service Instructions carefully, and keep them in a safe place for later reference.
Multi-Condition Brake System
Multi-Condition Brake System
By providing superior wet weather braking performance (control and modulation), braking performance will not vary in a multitude of conditions when using this brake system.
1 mm
5 mm Allen key
Tightening torque: 6 8 N·m {52 69 in. lbs. }
In order to realize the best performance, we recommend that the following combination be used.
Series Brake lever V-BRAKE brake Brake cable DXR BL-MX70 BR-MX70
4. Pass the inner cable through the inner cable lead, and
after setting so that the total of the clearances between the left and right shoes and the rim is 2 mm, tighten the cable fixing bolt.
Inner cable lead
5 mm Allen key
Installation of the brake lever
Use a 5 mm Allen key to install the brake lever.
Tightening torque: 6 8 N·m {52 69 in. lbs. }
5 mm Allen key
Tightening torque: 6 8 N·m {52 69 in. lbs. }
Use a handlebar grip with a maximum outer diameter of 32 mm.
BL-MX70
JAPAN 22. 2
BC
B + C = 2 mm
5. Adjust the balance with the spring tension adjustment
Shimano BR-MX70 Safety Information
WARNING
To avoid serious injuries:
When installing the components to carbon frame/handle bar surfaces, verify with the manufacturer of the carbon frame/parts for their recommendation on tightening torque in order to prevent over tightening that can cause damage to the carbon material and/or under tightening that can cause lack of fixing strength for the components.
screws.
2
1
Use the BR-MX70 V-BRAKE brake with V-BRAKE brakecompatible brake levers such as the BL-MX70 brake levers.
Note
· The optimum efficiency of the Multi-Condition Brake System can be realized by using the brakes and brake levers in the recommended set. · If the brake shoes have worn down until the grooves are no longer visible, they should be replaced. Ask the place of purchase for details when purchasing the brake shoes. · Parts are not guaranteed against natural wear or deterioration resulting from normal use. · For maximum performance we highly recommend Shimano lubricants and maintenance products. · For any questions regarding methods of handling or maintenance, please contact the place of purchase.
Spring tension adjustment screw
Spring tension adjustment screw
Installation of the V-BRAKE brake
1. [. . . ] XBC IZM Printed in Malaysia.
Washer Washer A Washer A Shoe fixing link
3. Insertion of shoe fixing pin is very critical to keep shoe
properly fixed in place.
R
L
FORWARD
FORWARD
L [. . . ]
DISCLAIMER TO DOWNLOAD THE USER GUIDE SHIMANO SI-0071A
Click on "Download the user Manual" at the end of this Contract if you accept its terms, the downloading of the manual SHIMANO SI-0071A will begin.