User manual SHIMANO SI-R650F TECHNICAL INSTRUCTIONS

DON'T FORGET : ALWAYS READ THE USER GUIDE BEFORE BUYING !!!

If this document matches the user guide, instructions manual or user manual, feature sets, schematics you are looking for, download it now. Diplodocs provides you a fast and easy access to the user manual SHIMANO SI-R650F. We hope that this SHIMANO SI-R650F user guide will be useful to you.


SHIMANO SI-R650F TECHNICAL INSTRUCTIONS: Download the complete user guide (590 Ko)

Manual abstract: user guide SHIMANO SI-R650FTECHNICAL INSTRUCTIONS

Detailed instructions for use are in the User's Guide.

[. . . ] Because of this, an excessive load may be placed on the drive system if the chain length is too short. Set the length of the chain by adding two links to the chain when the rear suspension is at a position where dimension "A" is longest and the chain is on the largest sprocket and the largest chainring. If the amount of movement of the rear suspension is large, the slack in the chain may not be taken up properly when the chain is on the smallest chainring and smallest sprocket. Largest sprocket Chain Largest chainring A' Cassette sprocket tooth combination Model number CS-M750 CS-M750 CS-M750 CS-HG70-9 Group name as aQ ap ar Gears 9 9 9 9 Tooth combination 11, 13, 15, 17, 20, 23, 26, 30, 34T 11, 12, 14, 16, 18, 21, 24, 28, 32T 12, 14, 16, 18, 20, 23, 26, 30, 34T 11, 12, 14, 16, 18, 21, 24, 28, 32T A SIS Adjustment Shifting lever Model number Gears ST-M750 / SL-M750 9 ST-M570 / SL-M570 9 1. Top adjustment Turn the top adjustment screw to adjust so that the guide pulley is in line with the outer line of the smallest sprocket when looking from the rear. 1 2 Outer line of smallest sprocket Note regarding the sealed cap with tongue, rubber shield and outer casing adjustment barrel cover 1. [. . . ] Apply grease from the end with the marking in order to maintain cable operating efficiency. 4. How to use the B-tension adjustment screw Marking Cutting the outer casing Tightening torque : 6 - 8 N·m {53 - 69 in. lbs. } SL-M750 / SL-M570 5 mm Allen key ST-M750 / ST-M570 When cutting the outer casing, cut the opposite end to the end with the marking. After cutting the outer casing, make the end round so that the inside of the hole has a uniform diameter. Outer end cap Tightening torque : 5 N·m {44 in. lbs. } Attach the same outer end cap to the cut end of the outer casing. 5 mm Allen key Mount the chain on the smallest chainring and the largest sprocket, and turn the crank arm backward. Then turn the B-tension adjustment Largest sprocket Smallest sprocket screw to adjust the guide 2 2 pulley as close to the sprocket as possible but not so close that it touches. Next, set the chain to the smallest sprocket and 12 repeat the above to make 1 sure that the pulley does B-tension not touch the sprocket. adjustment screw 1 U. S. PAT 4268 25 9 The groove is wide at one place only. U. S. PAT 4268 25 9 U. S. PAT 4268 25 9 -C J AP Assembly 10 mm Allen key (TL-WR37) 1. Remove the two indicator set screws which are securing the indicator. Tightening torque : 0. 3 - 0. 5 N·m {3 - 4 in. lbs. } Lock ring · To replace the sprockets, use the special tool (TL-HG16) and TL-SR20 to remove the lock ring. Lock ring Tightening torque : 35 - 50 N·m {305 - 434 in. Remove the indicator unit as shown in the illustration. Indicator set screws Indicator H IM A NO HYP E RG DE LI -C J AP Tool (TL-SR20) 3. Operate lever (B) at least eight times to set the lever to the highest position. Lever (B) AN TL-HG16 Disassembly DE LI -C J AP Gear shifting operation Both lever (A) and lever (B) always return to the initial position when they are released after shifting. When operating one of the levers, always be sure to turn the crank arm at the same time. AN To shift from a small sprocket to a larger sprocket To shift one step only, press lever (A) to the (1) position. A maximum three-step shift can be made in this manner. Lever (A) initial position 4. After checking that the indicator needle 1 2 is at the left edge, install the indicator as shown in the illustration. AN U. S. PAT 4268 25 9 5. If it does not operate To shift from a large sprocket to a smaller sprocket Press lever (B) once to shift one step from a larger to a smaller sprocket. correctly, re-install the indicator while taking particular note of steps 3. to 4. Replacement of the shifting lever unit Disassembly and reassembly should only be carried out when replacing the shifting lever unit. Lever (B) 1. [. . . ] (clockwise) * Turn the outer casing adjustment barrel together with the outer casing adjustment barrel cover. Loosen the outer casing adjustment barrel until the chain touches the 3rd sprocket and makes noise. (counter clockwise) * Turn the outer casing adjustment barrel together with the outer casing adjustment barrel cover. Low adjustment screw Best setting The best setting is when the shifting lever is operated just enough to take up the play and the chain touches the 3rd sprocket and makes noise. * Return the lever to its original position (the position where the lever is at the 2nd sprocket setting and it has been released) and then turn the crank arm clockwise. If the chain is touching the 3rd sprocket and making noise, turn the outer casing adjustment barrel clockwise slightly to tighten it until the noise stops and the chain runs smoothly. This service instruction explains how to use and maintain the Shimano bicycle parts which have been used on your new bicycle. For any questions regarding your bicycle or other matters which are not related to Shimano parts, please contact the place of purchase or the bicycle manufacturer. ® These service instructions are printed on recycled paper. One Holland, Irvine, California 92618, U. S. A. [. . . ]

DISCLAIMER TO DOWNLOAD THE USER GUIDE SHIMANO SI-R650F




Click on "Download the user Manual" at the end of this Contract if you accept its terms, the downloading of the manual SHIMANO SI-R650F will begin.

 

Copyright © 2015 - manualRetreiver - All Rights Reserved.
Designated trademarks and brands are the property of their respective owners.