Detailed instructions for use are in the User's Guide.
[. . . ] SI-4G60A-002-00
General Safety Information
WARNING
Before use, check the wheels to make sure that there are no bent or loose spokes, dents, scratches or cracks on the rim surface. With these types of forks, the clearance between the hub axle and the brake shoes can change due to the operation of the suspension, so that when the brakes are applied, the brake shoes may touch the spokes. If the quick release mechanism is not used correctly, the wheel may come off the bicycle and serious injury could result. Read the Service Instructions for the quick release mechanism thoroughly before use. [. . . ] (If using a 10-gear sprocket set other than for a junior bicycle, use the accessory 1-mm spacer. ) Refer to the Product Technical Information for details on combination with other parts such as chains and cassette sprockets.
Specifications
Series Model number Speeds Rim size Rim width Rim height For front For rear DURA-ACE WH-7900-C35-CL 8 / 9 / 10 700C (622 × 15C) 20. 8 mm 35 mm 35 mm For front are secured. 11T - 21T 11T - 23T 11T - 25T 11T - 27T 11T - 28T 12T - 23T 12T - 25T 12T - 27T 11T, 11T, 11T, 11T, 11T, 12T, 12T, 12T, 12T, 12T, 12T, 12T, 12T, 13T, 13T, 13T, 13T, 13T, 13T, 13T, 13T, 14T, 14T, 14T, 14T, 14T, 14T, 14T, 14T, 15T, 15T, 15T, CS-7900 15T, 16T, 15T, 16T, 15T, 17T, 15T, 17T, 15T, 17T, 16T, 17T, 16T, 17T, 16T, 17T, 17T, 17T, 19T, 19T, 19T, 18T, 19T, 19T, 18T, 19T, 21T, 21T, 21T, 19T, 21T, 21T, 19T, 21T, 23T, 24T, 24T, 21T, 23T, 24T, 21T 23T 25T 27T 28T 23T 25T 27T 1000 - 1400 N (224 - 314 lbf) Spoke tension value For rear Right (sprocket) side Left side 1200 - 1500 N 600 - 900 N (269 - 336 lbf) (134 - 202 lbf)
Cassette sprocket
Sprockets marked by Model No.
* These values should be used as a guide only.
CAUTION
The tires should be inflated to the pressure indicated on the tires before use. Use rim tape which can withstand high pressures, otherwise the tires may suddenly puncture and come off, and severe injury may result.
Sprocket tooth configuration
Installation of the HG sprockets
For each sprocket, the surface that has the group mark should face outward and be positioned so that the wide parts of the gear projections on each sprocket and the A part (where the groove width is wide) of the freewheel body are aligned.
A
Wide part
ac-14T
11T - 21T, 11T - 23T
NOTICE
The Shimano R55HC (high performance) brake shoes use an aggressive compound designed with an emphasis on maximum performance in wet conditions, however they will cause accelerated rim wear. Shimano accepts no responsibility for reduced rim life which might occur from using R55HC brake shoes. If non-Shimano parts are used, the area where the spokes fit into the hub unit may become damaged. Before use, check that there are no pieces of metal or other foreign objects sticking to the brake pads. If any such items are present, they may cause damage to the rim when the brakes are applied. The nipples have large diameters and are easy to rotate in order to make it easier to increase the spoke tension. However, be careful not to overtighten the nipples when adjusting the spoke tensions. (We recommended that you ask authorized bicycle dealers to make the adjustments. )
Replacing the spokes
Hook the spokes through the hub as shown in the illustration to install them. At the front, fit the heads of the spokes securely into the slots in the hub unit, otherwise damage may occur.
*1 Inner ring
For installation of the HG sprockets, use the special tool (TL-LR15) to tighten the lock ring. lbs. } To replace the HG sprockets, use the special tool (TL-LR15) and TL-SR21 to remove the lock ring.
Spacer
Sprocket spacers
Lock ring
11T - 25T, 11T - 27T, 11T - 28T
*2 Hub cap Spoke *2 Hub cap
The groove is wide at one place only.
When installing the CS-7900 (10-gears) freehub, install a spacer in the position shown in the illustration.
Spacer
Sprocket spacers
Lock ring
Lock ring
12T - 23T, 12T - 25T, 12T - 27T
TL-LR15 Tool (TL-SR21)
Note:
If the wheel becomes stiff and difficult to turn, you should lubricate it with grease. Do not apply any oil to the inside of the hub, otherwise the grease will come out. We recommend that you ask authorized bicycle dealers to adjust the spoke tensions if there is any initial play in the spokes and after the first 1, 000 km of riding. For maximum performance we highly recommend Shimano lubricants and maintenance products. Model number RR-550-WUWSW RR-550-WUASW RR-317-WUASW Specification CPSC AS DIN Color White Amber Amber
Nipple
*1 Install the inner ring so that it is fully set inside the tabs of the hub unit. [. . . ] Be sure to apply grease to the the thread of the freewheel body fixing bolt, otherwise looseness or sticking may occur. Do not disassemble the freewheel or apply oil or grease to it, otherwise problems with operation may occur.
Disassembly
One Holland, Irvine, California 92618, U. S. A. Phone: +1-949-951-5003
SHIMANO AMERICAN CORPORATION
14 mm Allen key
Industrieweg 24, 8071 CT Nunspeet, The Netherlands Phone: +31-341-272222 3-77 Oimatsu-cho, Sakai-ku, Sakai-shi, Osaka 590-8577, Japan
SHIMANO EUROPE B. V.
SHIMANO INC.
© Nov. [. . . ]