User manual SIEMENS EH957501E

[. . . ] EN Instruction manual 3 Table of contents Important information . Only after read ing these will you be able to operate the appliance correctly. If the appliance is passed to another per son, please enclose the instructions. Before switching on your appliance Transport damage Check your appliance after removing the packaging. If it has suffered any damage during transport, do not connect the appliance but contact the Technical Services department. [. . . ] If the zone referred to is not switched off, the letter x and the power level j in the hotplate indicator will flash; it will return to the maximum power level setting (j). In hotplate number 3, the Powerboost function can be activated at any time, so long as the outer cooking zone (number 4) is not working (see picture). Grupo 2 19 This is how to activate it Carry out the following steps: 1. When it is in this position press the + symbol for the zone concerned. The Powerboost function has been deactivated. Using Powerboost function in hotplate 4 This function can only be activated when the outer zone is working and cooking zones 3 and 4 are not activated. If cooking zone 3 or 4 is switched on when the Powerboost function is activated, the zone display will flash x and j alternately before returning to the maximum power level 9. How to activate it Follow the steps below: 1. The Powerboost function will have been disconnected. d 20 In certain circumstances, the Powerboost func tion may be deactivated automatically to protect the internal electronic components of the hob. Timer function This function can be used in two different ways: - to switch a hotplate off automatically - as a cooking timer A hotplate is to switch off automatically Setting procedure You enter a specific cooking time for the desired hotplate. When the cooking time has elapsed, the hotplate switches off automatically. 1. Set the heat setting on the hotplate which is to be operated with the timer function. 2. If you select a different hotplate, touch the and symbols repeatedly and at the same time until the 1 indicator for the required hotplate flashes. 3. For : 30 minutes For : 10 minutes The 1 indicator for the hotplate flashes again. 4. Touch the or symbol until the desired cooking time appears in the timer indicator. If you have set a cooking time for several hotplates, it is always the shortest cooking time that is displayed. The 1 hotplate indicators light up. 21 When the cooking time has elapsed When the cooking time has ended, the hotplate switches off. Touch the and symbols repeatedly and at the same time until the required 1 indicator flashes. Touch the and symbols repeatedly and at the same time until the required 1 indicator flashes. If you would like to call up the remaining cooking time for a hotplate: Touch the and symbols repeatedly and at the same time until the 1 indicator for the relevant hotplate flashes. The timer function is no longer active after a power cut. Changing the cooking time Cancelling prematurely Notes Cooking timer Setting procedure You can use the timer on your cooker to set a time of up to 99 minutes. Touch the and symbols repeatedly and at the same time until the a indicator for the cooking timer flashes. Set the time using the and symbols. The time disappears after a few seconds. The shortest time set with the timer is displayed. 22 When the cooking time has elapsed A signal sounds when the cooking time has elapsed. Touch the and symbols repeatedly and at the same time until the a indicator for the cooking timer flashes. The cooking timer is no longer in operation after a power cut. When the cooking time has elapsed Changing the time Note Memory function You can use the memory function to store the heat settings and times for one meal which can be called up again at any time. [. . . ] The cooking hob is too hot and has turned off. F4 F8 The cooking zone has been working at a high power and continuously for too long. If the indication continues, notify the technical assistance service. o2/o3 The cooking zone has overheated. The cooking hob is not well connected. U400 30 Normal operating noises for the appliance Induction heating technology is based on the vibration resistance of certain metals when subjected to high frequency waves. In some circumstances, these vibrations can cause a certain degree of noise, such as the following: This occurs when cooking at a high power. [. . . ]