User manual SIEMENS GIGASET 8825 QUICK START GUIDE

[. . . ] If you have a single line, plug the single connector into the wall and the two other ends into the back of the base unit. It will not damage phone to plug it into L2 if you only have one phone line. Base Station Setup 2 3 Bottom view of base L2 L1(+L2) 1 IMPORTANT: You are now ready to use the corded handset. See other sections of this Quick Start Guide for additional base setup and cordless handset setup. For best reception, place the base in a high central location, away from other electrical devices. [. . . ] Press the RIGHT side of the RIGHT soft key to select (OK). Left Soft Key Press the RIGHT side of the LEFT soft key to scroll down. Right Soft Key Press the LEFT side of the RIGHT soft key to return. PIN Number Setup At the Base Station: 1 2 3 4 5 6 7 8 Press 0(18 . 768F1 6(/(&7 3AX9 Scroll to System Settings?and press 6(/(&7 Press BACK < and > FWD buttons to scroll. . Default PIN number is 0000. 6(/(&7 Enter the default PIN (0000) and press . 6(/(&7 Scroll to Change System PIN?and press press . Enter a 4-digit PIN (do not use # or *) that is easy to remember and 6(/(&7 . The display will prompt Repeat New System PIN. 6(/(&7 Enter your new PIN again and press Press to exit. . The display will confirm New PIN Set. 0(18 IMPORTANT: The system PIN protects settings of the entire system. You must change the default PIN (0000) in order to access the answering machine remotely. Area Code Setup If you subscribe to Caller ID from your local telephone company, complete the steps below for your 7-digit or 10-digit dialing area. If you do not have Caller ID, skip this section. At the Base Station: 768F1 6(/(&7 3AX9 LOCAL DIALING AREA 1 2 3 4 5 6 7 Press BACK < and > FWD buttons to scroll. Press 0(18 . Default PIN number is 0000. 6(/(&7 Scroll to System Settings?and press Enter your area code and press Press 0(18 . 6(/(&7 Enter the default PIN (0000) or your new PIN and press 6(/(&7 . . 6(/(&7 Scroll to Local Area Code?and press 6(/(&7 . . to exit. IMPORTANT: Setup of your area code is necessary for accurate dialing of local numbers from the call log. EXTRA AREA CODES These should be entered if your area includes more than one local area code. 1 2 3 4 5 6 7 8 Press 0(18 . 6(/(&7 Scroll to System Settings?and press . . 6(/(&7 Enter the default PIN (0000) or your new PIN and press 6(/(&7 . Scroll to Extra Area Code 1?and press Enter your extra area code and press 6(/(&7 6(/(&7 . . Scroll to Extra Area Code 2?and Extra Area Code 3?Press 0(18 to exit. IMPORTANT: Leave the Local Area Code option blank in a 10-digit dialing area (metropolitan areas). Setup of your area codes is necessary for accurate dialing of local numbers from the call log. Enter 000 to erase any existing area code. Basic Phone Operation At the Base Station: Making a Call 1 Lift corded handset, or press GDI@! or , or press 63. 5 for speaker phone. 3 Hang up to disconnect or press lit line key. GDI@ GDI@ Answering Call Pick up corded handset, or press lit or press 63. 5 for speaker phone. 087( or GDI@! , 1 2 3 4 Setting Volume 1 2 Intercom Call At the Handset: Lift corded handset. Hang up to disconnect or press lit , 17 , 17 . Lift corded handset or press 63. 5 . 087( Press to increase or press to decrease. Making a Call 1 Dial desired number. 3 Press or place handset in charger to hang up. 63. 5 63. 5 Answering Call Lift handset from charger or press !2 Enter handset number or 0 for base, , 17 or select ALL for all phones. 5 If on , press again to adjust volume. 63. 5 63. 5 Troubleshooting Symptoms and Possible Causes PHONE SYSTEM DOES NOT WORK AT ALL Make sure handset is powered-on. Make sure the power cord is plugged into the base and the electrical outlet is not controlled by a wall switch. [. . . ] Cycle power on base unit by unplugging power supply and plugging back in. CANNOT TRANSFER A CALL Make sure you are transferring to an active intercom number. CANNOT DIAL FROM CALL LOG Make sure you subscribe to local Caller ID service. Make sure the area codes, both local and extra, are set. Customer Care: 1-888-777-0211 or visit our Website: www. icm. siemens. com Visite nuestro sitio Web para obtener instrucciones en espaol. DO NOT RETURN THIS PRODUCT TO THE STORE! Please read the following important information. [. . . ]