User manual SIEMENS MOTION 501

[. . . ] Dispose batteries according to national regulations or return them to your Hearing Care Professional. In some countries restrictions for the usage of wireless equipment exist. Do not use your hearing instruments in areas where there is a danger of explosions (e. g. 8 Handling batteries Handling batteries original size Always use the right size batteries. [. . . ] If you hear an acoustic signal or experience low amplification power, replace the battery. 9 Handling batteries Inserting the battery Open the battery compartment. Insert the battery. Make sure the "+" symbols on the battery and compartment are aligned. Close the battery compartment. 10 Inserting and removing the hearing instrument Inserting and removing the hearing instrument Never pull on the battery compartment door or volume control wheel to remove the hearing instrument, as this could cause damage. Slightly twist and push the hearing instrument into its proper position. Removing Push lightly on the back of your ear to loosen the hearing instrument. Pull the hearing instrument out. 11 Turning your hearing instrument on and off Turning your hearing instrument on and off Ask your Hearing Care Professional to check off the relevant information. Via battery compartment Fully open the battery compartment to turn your hearing instrument off. Via program button Press and hold the button for 3 seconds to turn the instrument on or off. Via volume control with on/off-function Rotate the colume control down to the stop to turn your hearing instrument off. Via remote control Refer to the remote control user guide. 12 Turning your hearing instrument on and off Power-on delay Your hearing instrument is equipped with a "power-on delay" feature which can be activated by your Hearing Care Professional. This allows you to turn the hearing instrument on with an automatic delay of 6, 12 or 18 seconds, so that you may insert the hearing instrument into your ear without experiencing unpleasant feedback (whistling). 13 Changing the hearing program Changing the hearing program Ask your Hearing Care Professional to check off the relevant information. Via program button Press the button to change the program. Via remote control Refer to the remote control user guide. 14 Changing the volume Changing the volume The volume of your hearing instruments is controlled automatically and there is no need to manually adjust it. If the windscreen of your hearing instruments is soiled, ask your Hearing Care Professional to clean or exchange the windscreen. Ask your Hearing Care Professional for special care sets and further information on how to keep your hearing instruments in good condition. 19 Maintenance and care Wax protection Your hearing instruments are equipped with a sieve, recess or guard on the sound outlet to prevent earwax from entering the hearing instruments. Your Hearing Care Professional will provide you with the wax protection appropriate for your instruments and can advise you how to clean or replace it. If the instruments sound distorted or weak exchange the wax protection. 20 Accessories Accessories Tek wireless enhancement (not all hearing instruments) Your hearing instruments together with the Tek Connect remote control will allow you to connect your hearing instruments to the growing world of technology. Via a special Bluetooth connection it is possible to receive audio signals from your mobile, your television or your mp3-player. For detailed information and instructions refer to the Tek user guide or ask your Hearing Care Professional. Remote control (not all hearing instruments) The wireless function of your hearing instruments allows you to use a remote control to change the program and volume of your hearing instruments. For further information about the remote control, contact your Hearing Care Professional or refer to the remote control user guide. In the event your hearing instruments can be controlled by another person's remote control, return hearing instruments and remote control to your Hearing Care Professional. 21 Troubleshooting Troubleshooting Use these tips to resolve simple issues. Problem Sound is weak. Close battery door completely or press and hold the program button for approximately 2 seconds. Hearing instruReinsert the instrument until it fits ment emits whis- securely. [. . . ] 22 Technical information Technical information Siemens Motion 700 WL, Motion 500 WL, Motion 300 WL Siemens Motion 701 WL, Motion 501 WL, Motion 301 WL FCC ID: SGI-WL002ITE IC: 267AB-WL002 Operating frequencies: Fc=3. 28 MHz N14203 This Class B digital apparatus complies with Canadian ICES-003. Changes or modifications not expressly approved by SAT GmbH for compliance could void the users authority to operate the equipment. FCC compliance This device complies with Part 15 of the FCC Rules and with RSS-310 of Industry Canada. Operation is subject to the following conditions: this device may not cause harmful interference, and this device must accept any interference received, including interference that may cause undesired operation. [. . . ]