User manual SIEMENS WK16D540HK

[. . . ] SIEMENS Installation and operating instructions en Washer-dryer Please read the Installation and operating instructions and all the other information supplied and handle the appliance accordingly. Keep all documents in a safe place for later use or to pass on to subsequent owners. For further information and a selection of our products, please see our website: www. siemens-home. com Contents Operation instructions General safety information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Environmental protection/economy tips . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] (Start/Pause) button. i Pausing the programme The new programme starts. (Start/Pause) button while the programme is in progress until appears on the display panel. and the Remaining time 0 appear alternately on the display while the programme is paused. (Start/Pause) button to continue with the programme. Cancelling the programme Press and hold !(Start/Pause) until is displayed. For washing programmes at high temperatures: ­ Cooling down laundry: choose Rinse ' + Spin B. (Start/Pause) button. t If you cancel the drying programme, the laundry may still be very hot. 15 Washing and drying Washing only Turn the programme selector to the desired programme, e. g. ­ B (Remaining time) and the recommended load in kg appear alternately on the display panel. If necessary, adjust the temperature and the spin speed and select any options for your individualised programme ­> page 14. ­ Observe the maximum load capacity, Programme table --> page 30. ­ The washing programme starts. i Drying only Turn the programme selector to the desired drying programme. ­ The display panel alternately shows B (Remaining time) and the recommended load in kg. Press the ^ (Drying) button to set the drying options ­> page 14 ­ If you do not make a selection, the e (Cupboard-dry) option is set. ­ B (Remaining time) is shown on the display panel and the ^ (Drying) and M (Programme start) symbols light up. ­ The drying programme starts. i Washing and drying Successive washing and drying. ­ B (Remaining time) and the recommended load in kg appear alternately on the display panel. If necessary, adjust the temperature and the spin speed and select any options for your individualised programme ­> page 14. Press the ^ (Drying) button to set the drying options ­> page 15 Load the laundry ­> page 9. Press the M (Start/Pause) button. i The drying programme that is carried out is automatically determined by the washing programme, see the Programme table ­> page 30. 16 End of the programme The washing and drying programmes are ended automatically. Leave the door open so that the inside of the washer-dryer can dry out. Turn off the tap (not necessary on models with Aqua-Stop). Rinse Hold If the spin function was deactivated at the start of the wash cycle, $ (no final spin = laundry remains in last rinsing water), the washing programme is automatically stopped after the final rinse. In order to drain the rinsing water and, if required, spin the laundry: Press the B (Spin) button repeatedly until the required spin speed is set. If you do not wish to spin the laundry: Press the B (Spin) button (remaining time for draining is displayed). [. . . ] Only use the inlet hose supplied or one which was purchased from an authorised specialist retailer. Water supply Do not allow the water supply hose to be: ­ kinked or squashed ­ altered or cut (strength no longer guaranteed). Note the water pressure in the mains supply: The water pressure should be between 50-900 kPa (0. 5-9 bar) (at least 8 litres of water flow out per minute when the tap is turned on). If the water pressure is higher, a pressure reducing valve must be fitted. Connect the cold-water supply hose (blue union nut) to the cold water tap with ¾" pipe (3/4" = 26, 4 mm) thread. * depends on the model For hot water supply*, connect the hose with the red union nut to the hot water tap. [. . . ]