User manual SPECO SP-5NXC-T
DON'T FORGET : ALWAYS READ THE USER GUIDE BEFORE BUYING !!!
If this document matches the user guide, instructions manual or user manual, feature sets, schematics you are looking for, download it now. Diplodocs provides you a fast and easy access to the user manual SPECO SP-5NXC-T. We hope that this SPECO SP-5NXC-T user guide will be useful to you.
Manual abstract: user guide SPECO SP-5NXC-T
Detailed instructions for use are in the User's Guide.
[. . . ] Owner's Manual for Models:
SP-4NXC/T SP-5NXC/T SP-6NXC/T
200 New Highway Amityville, New York 11701 · Outside Metro NY: 1-800-645-5516 631-957-8700 · www. specotech. com
70/25V Commercial Speaker Systems
TM
TM
8. 04
Congratulations on your purchase of Speco Technologies' Nexus ContractorTM 70/25 Volt Commercial Speaker Systems!
Speco Technologies' Nexus ContractorTM Commercial Speaker System Line offers premium quality components and strong specification providing a network of sound and paging for the most demanding commercial environments.
Connecting and Mounting Your Speakers:
Please follow these directions for connecting and mounting your Nexus ContractorTM Commercial Speaker System: Silver Wattage Tap Dial Indicator
Easy Mount Tabs
The high-end NXC Series features heavy-duty, industrial metal back cans that provides component protection and safety while at the same time enhancing the speakers' full-range bass sound as does the speakers' ported design. Quick-snap terminal connects provide easy access and optimal angles for connecting speaker wire to the NXC Series as a wattage selector dial makes transformer wattage setting as easy as a quick turn. [. . . ] See following diagram: * Through this wiring method, if the quick-snap terminal connect is pulled out in the middle of a speaker run, subsequent speakers will stay connected.
Once the wires are in, firmly tighten the small screws above each terminal until the wires are firmly secured. Upon securing, gently snap the quick-snap terminal connects back into place making sure it is lined up properly and the text of the numbers on the quick-snap terminal connects match the same direction as the text of the positive/negative indications on the back of the speaker for proper fitting. Once the quick-snap terminal connect is in place, re-cover and the terminals section by securing the terminal metal cover to its original location. Upon securing the terminal metal cover, faster the screws on the strain-protector to secure and clamp down on the wires to prevent loosening during installation and post-installation. A 3/4" diameter punch out hole is also available on the terminal metal cover for installations where solid conduit or flex pipe is needed. In addition, a metal safety loop accompanies the back of each speaker and is recommended for securing a speaker run with a supporting cable. After connecting each speaker, it is recommended that you quickly check the connections with sound prior to final mounting installation to ensure that everything is installed properly and functioning well.
For an 8 ohms speaker requirement, turn dial tap so that the silver indicator aligns with the 8 ohms indication on the dial. This automatically overrides the transformer within the unit.
Connecting Speaker Wire
To correctly wire your speaker systems, carefully remove the terminal metal cover protecting the terminals on the back of your speakers by unscrewing the fastened screws in each of the two corners. When the terminal metal cover is removed, loosen the screws on the strain-protector portion of the terminal cover and pass the speaker wire through the strain-protector. After passing the pre-laid wire through the strain-protector, remove the gray-numbered quick-snap terminal connect from the back of the speaker by slowly pulling it straight out of the terminals. On desired Parallel Runs, use the positive wire entering from the amplifier to enter and leave through terminal #2. The common wire running back to the amplifier should enter and leave through terminal #3 to wire your run as shown in the following example: * Through this wiring method, if the quick-snap terminal connect is pulled out in the middle of a speaker run, subsequent speakers will stay connected.
Installation:
Upon determining you have a strong wire connection with your NXC Series speakers, they must be flush-mounted. [. . . ] Upon securing your speaker systems, replace the grilles back on the faceplate and you are finished to enjoy your high-quality Nexus ContractorTM Series speakers.
Speco Technologies' Top Selling Commercial Items
Warranty:
Speco Technologies offers a limited 15-year warranty on their indoor speakers. Please reference the enclosed warranty card for complete details of warranty.
30 or 60 Watt 4 Zone Amplifiers with AM/FM Tuner and CD Player Item Codes: P-30FACD, P-60FACD (Also available in cassette version)
15, 30, 60, 120 Watt RMS Contractor Series Amplifiers Item Codes: PBM-15, PBM-30, PBM-60 or PBM-120
Speco Technologies 200 New Highway Amityville, New York 11701 631-957-8700 www. specotech. com
70/25V MA Series ABS Plastic Enclosure Speakers Item Codes: SP-5MA/T, SP-6MA/T
70/25V Commercial Speakers Item Codes: G86TG, G86TCG (with Volume Control)
NOTES
70/25V 30 Watt Weatherproof Horn Item Code: SPC-30RT
70/25 5. 25" Outdoor Speakers Item Codes: SP-5AWD/T (Black), SP-5AWD/T-W (White) Available in 6. 5" also
Desktop MIC with XLR Connector Item Code: MHL-5S
70/25V Rock Speakers Item Code: SP-RK65CB/T (Brown), SP-RK65CG/T (Granite) [. . . ]
DISCLAIMER TO DOWNLOAD THE USER GUIDE SPECO SP-5NXC-T
Click on "Download the user Manual" at the end of this Contract if you accept its terms, the downloading of the manual SPECO SP-5NXC-T will begin.