User manual STRONG PRIMA V

[. . . ] Digital Terrestrial MPEG-4 HD Receiver PRIMA V User manual Picture similar PART 1 • English Table of Contents 1. 0 Introduction 1. 1 Safety Instructions 1. 2 Storage 1. 3 Equipment Set-up 1. 4 Accessories 1. 5 Usage of external USB devices 2. 0 Your Receiver 2. 1 PIN-CODE DEFAULT: 0000 2. 2 Front Panel 2. 3 Rear Panel 2. 4 Remote Control 3. 0 Connection 3. 1 Connecting to a Terrestrial Antenna 3. 2 Connecting to TV with HDMI cable 3. 3 Connecting to TV with SCART cable 3. 4 Connecting to a Digital Audio Amplifier with S    DIF  /P 3. 5 Connecting to a Digital Audio Amplifier and TV using HDMI 3. 6 Connecting a USB storage device 4. 0 Starting up for the first time 5. 0 Quick guide to using your receiver 6. 0 Operation 6. 1 Changing channels 6. 2 Info Banner 6. 3 Selection of audio language 6. 4 Teletext 6. 5 Subtitles 6. 6 Time Shift 6. 7 EPG (Electronic Programme Guide) 6. 8 Instant Recording 7. 0 Main Menu 7. 1 Edit Channel 7. 2 Installation 7. 3 System Setup 7. 4 Tools 7. 5 Games 7. 6 Media+ 8. 0 Troubleshooting 9. 0 Technical Specifications 2 2 2 3 3 3 3 3 3 4 4 5 5 5 5 5 5 5 6 7 7 7 8 8 8 8 8 8 9 9 9 11 12 14 15 16 17 18 23 Aug 2012 16:32 STRONG declares that this item complies with the basic requirements and other relevant regulations of directives 2004/108/EC and 73/23/EC, RoHS 2002/95/EC Subject to alterations. In consequence of continuous research and development technical specifications, design and appearance of products may change. All product names are trademarks or registered trademarks of their respective owners. All rights reserved. 1 English PART 1 • English 1. 0 Introduction 1. 1 Safety Instructions DO NOT INSTALL YOUR RECEIVER: In a closed or poorly ventilated cabinet; directly on top of or under any other equipment; on a surface which might obstruct the ventilation slots. [. . . ] The Skip symbol on the top of the screen will move up to indicate that the Skip function is selected. Use pq to select the achannel and press OK to mark or unmark it for skipping. Select Yes to save the changes or No to discard. 7. 1. 1. 4 Moving channels To enable the Move function, press YELLOW while in TV Channel List. The Move symbol on the top of the screen will move up to indicate that the Move function is selected. You can now move the selected channel up or down the channel list using pq. Select Yes to save the changes or No to discard. 7. 1. 1. 5 Editing channels The Edit function allows you to Sort, Rename or Delete channels. If you made changes in the previous menu, but not saved them yet, you will be asked to do so now. Possible methods are: Name (A-Z):  Sorting in alphabetical order from A to Z. All Default:  Sorting by searched Order (from lowest to highest frequency or by LCN numbering). Select Yes to save the changes or No to discard. 10 PART 1 • English Delete Press BLUE in Edit Channel to enable the Delete function. When you have marked all channels you wish to delete, press EXIT twice. Select Yes to delete the marked channels or No to cancel. Basically, the operation of the Radio Channel List is the same as in the TV Channel List. The only difference is that in Radio Channel List there is no video information, so it will always display the radio logo at the right preview screen. 7. 1. 2 Radio Channel List 7. 1. 3 Delete all Use this menu to delete all stored channels. In the confirmation window select Yes with tu and press OK to delete or select No to cancel. Warning!  Delete all function will permanently delete all current channels and all The favourite lists from your receiver, and you are not able to leave the menu until you search for channels again. 7. 2 Installation 7. 2. 1 Auto Scan Use pq to select Installation and press OK or u to advance. When FTA Only is set to Yes, scrambled channels won’t be stored in the channel list. The receiver will store all newly found channels in the channel list. 7. 2. 2 Channel Scan Use pq to select Installation, press OK or u to advance. Use tu to toggle between available scan modes:  Channel and By Frequency. By If By Channel is selected, use the cursor buttons to select Scan Band and Channel No. If By Frequency is selected, use the cursor buttons to select Frequency and Bandwidth. Newly found channels will be stored in the channel list. 7. 2. 3 Aerial Adjustment Use pq to select Installation, press OK or u to advance. Use pq move the highlight to the setting you wish to alter and use tu to change values. [. . . ] The help banner at the bottom of the screen explains all buttons used in the Media player. Note:  can also access the Media Player from viewing mode with the FILE You button on the remote control. 7. 6. 1 Media Player 7. 6. 2 Record Manager The Record Manager gives you access to previously recorded events. Select Record Manager from the Media+ menu and press OK to enter. Use pq to highlight the recording you wish to play and press OK start playback. [. . . ]