User manual STRONG SRT 5246

[. . . ] Digital Satellite and Terrestrial Receiver SRT 5246 User Manual Picture similar PART 1 · English TABLE OF CONTENTS 1. 0 INTRODUCTION 1. 1 Safety Instructions 1. 2 Storage 1. 3 Equipment Set-up 1. 4 Features & Accessories 2 2 3 3 4 2. 0 YOUR RECEIVER 2. 1 Front Panel 2. 2 Rear Panel 2. 3 Remote Control Unit 3. 0 CONNECTIONS 3. 1 Connecting to Satellite Dish 3. 2 Connecting to Terrestrial Antenna 3. 3 Connecting to TV & VCR 3. 4 Connecting to Digital Audio Amplifier 3. 5 Connecting to computer by serial cable for downloading software 5 5 5 6 8 8 8 8 8 9 4. 0 STARTING UP FOR THE FIRST TIME 5. 0 MAIN MENU 5. 1 Channel Organiser 5. 2 Satellite set-up 5. 3 Terrestrial set-up 5. 4 Installation 5. 5 Timer 5. 6 Games 6. 0 OTHER OPERATIONS 6. 1 Program Guide (EPG) 6. 2 Zapping and information banners 6. 3 Channel list and view mode A. 1 TROUBLESHOOTING A. 2 SPECIFICATIONS 9 10 10 12 16 17 19 19 20 20 20 20 22 22 1 English PART 1 · English 1. 0 INTRODUCTION 1. 1 Safety Instructions Grounding, Polarization -- If this product is used with a specified AC adapter, the adaptermay be equipped with a polarized alternating current line plug (a plug with one blade wider than the other). This safety feature allows the plug to fit into the power outlet only one way. If you cannot insert the plug into the wall outlet, pull it out, reverse it, and then reinsert it. If the plug still fails to fit, contact an electrician and have the receptacle replaced n Protecting the Power Cord -- The power supply cord should be placed so it will not bewalked on. [. . . ] n if mode of selected dish is "DiSEqC 1. 2" then value can be "Not stored" (in case dish position for selected satellite was not stored) or in range from 1 to 64 if position has been stored. n if mode of selected dish is "GOTO X" then value is "GOTO X". List of transponders of selected satellite will appear at right side of the screen. You can select transponder in order to check signal strength and quality of reception. If you need to modify transponder list please use menu "Edit satellites" as described in chapter 5. 2. 3. If you need to scan specific transponder then use Manual scan as described in this chapter below. Network search: if this item is set to "OFF" then receiver will search for the channels that are available from preset transponder list of selected satellite. If this item is set to "ON" then receiver in addition will search for the channels from transponders information about that can be found from broadcast. Search for: you can select type of the channels that will be installed to your receiver. n If selected "All channels" then receiver will install Free-To-Air and Scrambled channels n If selected "Scrambled" then receiver will install only Scrambled channels n If selected "FTA" then receiver will install only Free-To-Air channels Once you complete all settings you can start channel search process. Press RED button to setup channels from all transponders of the satellite; Press GREEN button to setup channels from transponder selected in Transponder item; Press YELLOW button to enter to Manual setup channels from specific transponder or to setup single channel with known Video and Audio PID. 13 English PART 1 · English Manual setup of channels In Manual channel search menu you can setup all channels from specific transponder or single channel. To setup all channels from specific transponder: Satellite: Indicate name of the satellite where channels will be searched Frequency: Use Numeric buttons to enter frequency of transponder Polarisation control: Use tupq buttons to select polarisation of transponder Symbol rate: Use Numeric buttons to enter symbol rate value Network search: Use tupq buttons to select ON or OFF Search for: Use tupq buttons to select type of channels to be installed Press RED (Search) button to start channel search. 5. 2. 1. 1 Positioner setup If in Dish setup menu you have configured Dish mode as "DiSEqC 1. 2" then you have to setup position of the dish to each satellite that you want to install. In Channel setup menu move menu focus to Dish position item and press OK button on remote control. Satellite: Displays the name of satellite position of antenna for which you setup Transponder: Use tu buttons to select reference transponder, receivable in your location, to measure signal strength and quality Movement speed: Use tu buttons to select between Slow and Fast. Slow speed allows you to fine adjust position of the dish. Fast speed can be used to adjust dish position roughly. Move: Use tu buttons to move dish to the East/West direction Centre position: If you press OK button while menu focus is on this item then dish will be turned to centre position, which corresponds to true South direction. Limits: Use tu buttons to Enable or Disable software limits of your positioner. Set limit: Use tu buttons to select East or West limit of dish movement range. n Select reference transponder in order to check signal strength and quality during position setup. n If you do not know current direction of your dish then move menu focus to Centre position item and press OK. Dish will be turned to true South. Knowing your location longitude you may understand direction where necessary to move dish in order to reach position of selected satellite. For example: your longitude is 5° East and you want to setup dish position for Astra 1C, 1E (19° East). [. . . ] To disable subtitles select OFF from the list of the languages. 21 English PART 1 · English A. 1 TROUBLESHOOTING There may be various reasons for the abnormal operation of the receiver. Check the receiver according to the procedures shown below. If the receiver does not work properly after checking it, please contact the dealer. Don't open the receiver cover. This may cause a dangerous situation. Symptom The LED display on front panel does not light up No picture or sound No picture Cause The power cord is not plugged in Wrong connection of the Audio/ Video output of the receiver to TV. TV power off The receiver can't receive the signal Incorrect values of some tuner parameters. Wrong direction of the dish Remedy Check that the power cord is plugged in to the wall outlet Connect the Audio/ Video output of the receiver to TV correctly. [. . . ]