User manual STRONG SRT 6004 EVOLUTION

[. . . ] Digital Free-To-Air Satellite Receiver SRT 6004 /6011 User Manual Picture similar PART 1 · English TABLE OF CONTENTS 1. 0 INTRODUCTION 1. 1 Safety Instructions 1. 2 Storage 1. 3 Equipment Set-up 1. 4 Features & Accessories 2. 0 YOUR RECEIVER 2. 1 Front Panel 2. 2 Rear Panel 2. 3 Remote Control 3. 0 CONNECTIONS 3. 1 Connecting to TV & VCR 3. 2 Connecting to Digital Audio Amplifier 3. 3 Connecting to Satellite Dish 3. 4 Connecting to serial cable for downloading software 4. 0 STARTING UP 4. 1 Language Selection 4. 2 Select Satellite 4. 3 Antenna mode 5. 0 MAIN MENU 5. 1 Channel Organiser 5. 2 Installation 5. 3 System setting 5. 4 Timer 5. 5 Game 5. 6 Calendar 6. 0 WATCHING TV AND LISTENING TO THE RADIO 6. 1 Program Information 6. 2 Mosaic (Nine picture view) 6. 3 EPG (Electronic Program Guide) 6. 4 Changing channel list mode between TV, Radio and Favourite 6. 5 Selection Audio Language 6. 6 TELETEXT function 6. 7 Subtitles function A. 1 TROUBLESHOOTING A. 2 SPECIFICATIONS A. 3 GLOSSARY OF TERMS 2 2 3 3 4 5 5 5 6 7 7 7 7 8 8 8 8 8 9 9 10 11 14 15 15 16 16 16 16 16 17 17 17 17 18 20 English 1 PART 1 · English 1. 0 INTRODUCTION 1. 1 Safety Instructions DO NOT INSTALL YOUR RECEIVER: n In a closed or poorly ventilated cabinet; directly on top of or under any another equipment; on a surface which might obstruct the ventilation slots DO NOT EXPOSE THE RECEIVER OR ITS ACCESSORIES: To direct sunlight or near any other equipment that generates heat; to rain or intense moisture; to intense vibration and to any shock which may cause permanent damage to your receiver or to any magnetic objects, such as loudspeakers, transformers, etc n Do not use a damaged power cord. It is dangerous to touch the inside of the receiver due to high voltage currents and possible electrical hazards. Your warranty will be void if the receiver has been opened n When the receiver is not used for a long period of time, you should unplug the power cord from the wall socket n Do not use alcohol or ammonia based liquids to clean the receiver. If you wish, you may clean your receiver with a soft lint-free cloth slightly made damp with a mild soap solution, only after disconnecting from the mains voltage supply. [. . . ] Blind scan function is useful to scan new added satellite, but scan may take long time. Press the BLUE Key to set the scan type to NIT OFF or NIT ON while Blind Scan is set to OFF and to Quick Search or Detail Search while Blind Scan is set to ON. When the set-up is completed, press the RED key to start the scan, shown as below. 5. 2. 3 Manual Scan In this menu, you can scan single transponder, add a new transponder, edit the transponder or delete the transponder. You can switch between satellites with the RED button, Scan transponder: Use UP/DOWN buttons to select the transponder. Add Transponder: In this menu, you can add a new transponder to the system. Edit Transponder: In this menu, you can edit a transponder in the system. Press LEFT/RIGHT to select OK, press the OK button to confirm. 5. 3 System setting In this menu, you configure the system, such as Language Setting, OSD style, Parental Control, TV Settings and Time Setting. 11 English Delete satellite If you want to delete a satellite, press the YELLOW key. Select OK and press the OK key to confirm. PART 1 · English 5. 3. 1 Preference 5. 3. 1. 1 Language Setting You can change the language of the OSD, preferred Audio and Subtitles. Use UP/DOWN to select the OSD language, Audio language or Subtitles language. Press OK or Right to enter the language list and Press UP/DOWN to select the language. Press OK to confirm. 5. 3. 1. 2 TV settings You can set the TV mode, Screen mode and Video output. TV mode In TV mode Screen press OK or RIGHT to select mode, press OK to confirm. If you don't know which standard your TV has, please select AUTO. n Screen mode In TV format Screen press OK or RIGHT to select 4:3 or 16:9, press OK to confirm. n Video output In Video output Screen press OK or RIGHT to select CVBS or RGB, press OK to confirm. n 5. 3. 1. 3 Time Settings If a broadcaster provides GMT, you can set the time using GMT, or set your own time by yourself. If you set GMT Usage to OFF, Set Data and Set Time item are displayed. To set the time value manually, move the cursor to the time item and use the numeric buttons on the remote control. 5. 3. 1. 4 Set Factory Default Please be careful when using this function, because it will erase all the data and parameters you may have set earlier to your receiver. Once you set the factory default you will have to re-install your preferences and re-scan your channels. To reset your receiver to factory default, apply the following steps: Select Set Factory default and press OK. Confirm warning message with OK and press the OK key, the receiver will return to its factory default state, and all user data will be deleted. NOTE: Your PIN code will change back to the factory setting "0000". 5. 3. 2 OSD Style In this menu, you can set the Menu Colour, Transparency Level and Border Pattern. 5. 3. 3 Parental Control In this menu, you can set Channel Lock status (ON or OFF), the Menu Lock status, Parental Setting and change the PIN code. The default PIN code is 0000. 12 PART 1 · English 5. 3. 3. 1 Channel Lock English 13 Set the system Channel Lock to ON or OFF. [. . . ] If channel has subtitles information the Subtitles language selection menu will appear. Press OK to confirm your selection. A. 1 TROUBLESHOOTING There may be various reasons for the abnormal operation of the receiver. If the receiver does not work properly after checking it, please contact the dealer. No picture The receiver can't receive the signal Remedy Check that the power cord is plugged in to the wall outlet. [. . . ]