User manual STRONG SRT 6011

[. . . ] Digital Free-To-Air Satellite Receiver SRT 6011 User Manual Picture similar SAFETY INSTRUCTIONS Grounding, Polarization -- If this product is used with a specified AC adapter, the adaptermay be equipped with a polarized alternating current line plug (a plug with one blade wider than the other). This safety feature allows the plug to fit into the power outlet only one way. If you cannot insert the plug into the wall outlet, pull it out, reverse it, and then reinsert it. If the plug still fails to fit, contact an electrician and have the receptacle replaced n Protecting the Power Cord -- The power supply cord should be placed so it will not bewalked on. [. . . ] After selection of a satellite from the satellite list, the Configure Antenna menu will appear, please set the LNB Type, LNB Low Freq, LNB High Freq, Band control, Polarisation control, DiSEqC Switch and Antenna mode. n Edit satellite If the parameters of the satellite were changed or the satellite is a new satellite, you must set the parameters of the satellite, such as LNB type, LNB low Freq, LNB High Freq, Transponder, LNB Power, 22k Tone, DiSEqC and Antenna Mode. Sequence of editing of satellite parameters is same as sequence of "Add satellite" described in 4. 2 9 English PART 1 · English n Delete satellite If you want to delete a satellite, press the YELLOW key. Select OK and press the OK key to confirm. 5. 2. 2 Auto Scan Press the GREEN key to set the scan mode to Free or Free+Scrambled. If mode is Free then only "Free to Air" channels will be added to the channel list. If mode is Free+Scrambled then all channels from selected satellite will be added to the channel list. Blind scan function is useful to scan new added satellite, but scan may take long time. Press the BLUE Key to set the scan type to NIT OFF or NIT ON while Blind Scan is set to OFF and to Quick Search or Detail Search while Blind Scan is set to ON. When the set-up is completed, press the RED key to start the scan, shown as below. 5. 2. 3 Manual Scan In this menu, you can scan single transponder, add a new transponder, edit the transponder or delete the transponder. You can switch between satellites with the RED button, Scan transponder: Use UP/DOWN buttons to select the transponder. Add Transponder: In this menu, you can add a new transponder to the system. Edit Transponder: In this menu, you can edit a transponder in the system. Press LEFT/RIGHT to select OK, press the OK button to confirm. 5. 3 System setting In this menu, you configure the system, such as Language Setting, OSD style, Parental Control, TV Settings and Time Setting. 10 PART 1 · English 5. 3. 1 Preference 5. 3. 1. 1 Language Setting You can change the language of the OSD, preferred Audio and Subtitles. Use UP/DOWN to select the OSD language, Audio language or Subtitles language. Press OK or Right to enter the language list and Press UP/DOWN to select the language. 5. 3. 1. 2 TV settings You can set the TV mode, Screen mode and Video output. n TV mode In TV mode Screen press OK or RIGHT to select mode, press OK to confirm. If you don't know which standard your TV has, please select AUTO. n Screen mode In TV format Screen press OK or RIGHT to select 4:3 or 16:9, press OK to confirm. n Video output In Video output Screen press OK or RIGHT to select CVBS or RGB, press OK to confirm. 5. 3. 1. 3 Time Settings If a broadcaster provides GMT, you can set the time using GMT, or set your own time by yourself. [. . . ] General Data Size(WxHxD): Weight: Operating Temperature: Storage Temperature: Operating Humidity Range: Storage Humidity Range: RGB, CVBS, Audio L/R Output with Volume Control Input: CVBS, Audio L/R Output: CVBS, Audio L/R Output with Volume Control Yellow: Video output; White: Audio Left; Red: Audio Right Digital audio output, coaxial RS-232, Bit Rate: 115200 baud 9-Pin D-Sub Male type 90 ~ 240 V AC, 50/60 Hz ±5% Max. 20 W <=8 W 260 x 40 x 210 mm 1. 2 kg 0 ~ 40 °C -30 ~ 80 °C 10 ~ 85 % RH, Non-condensing 5 ~ 90% RH, Non-condensing 18 PART 1 · English A. 3 GLOSSARY OF TERMS C band DiSEqC Fixed Dish Free-To-Air broadcast Ku band LNB 3. 7 ~ 4. 2 GHz Frequency. Unscrambled broadcast which you can view for free 11 ~ 13 GHz Frequency. It receives the signals reflected by the dish and converts them to signals that can be used by Satellite receiver. [. . . ]