User manual STRONG SRT 6015

[. . . ] 3 2 Introduction Safety Instructions Features & Accessories Safety Precautions Storage Equipment Set-up Your Receiver Front Panel Remote Control Unit Rear Panel Connections Connecting to TV & VCR Connecting to Digital Audio Amplifier Connecting to Satellite Dish Connecting to serial cable for downloading software Starting up Main Menu Channel Organiser Installation System setting Timer Game Other operation functions System Information Mosaic (Nine picture view) EPG (Electronic Program Guide) Selection Audio Language Teletext function Trouble Shooting Specifications Glossary of Terms 3 3 4 5 5 6 6 6 7 8 10 10 11 11 13 14 18 19 23 29 39 40 42 42 42 43 45 45 47 48 50 UM 6005-15 ENG 1/26/06 4:18 PM Page 3 PART 1 English 1. 1 Safety Instructions DO NOT INSTALL YOUR RECEIVER: In a closed or poorly ventilated cabinet; Directly on top of or under any another equipment; On a surface which might obstruct the ventilation slots. DO NOT EXPOSE THE RECEIVER OR ITS ACCESSORIES: To direct sunlight or near any other equipment that generates heat; To rain or intense moisture; To any shock which may cause permanent damage to your receiver; To any magnetic objects, such as loudspeakers, transformers, etc. It is dangerous to touch the inside of the receiver due to high voltage currents and possible electrical hazards. [. . . ] Press the OK button to add the selected channel to the Favorite group. 1 Antenna Installation You can add a satellite, edit a satellite and delete a satellite in this menu. SCREEN 19 Add satellite If you want add a new satellite, press the RED key in this menu, a satellite list will appear on the screen. If the satellite does not exist in the satellite list, please select “NEW SAT1”. SCREEN 20 24 UM 6005-15 ENG 1/26/06 4:18 PM Page 25 PART 1 English Edit satellite If the parameters of the satellite were changed or the satellite is a new satellite, you must set the parameters of the satellite, such as LNB type, LNB low Freq, LNB High Freq, Transponder, LNB Power, 22 k Tone, DiSEqC and Motor Position. SCREEN 21 Delete satellite If you want to delete a satellite, press the YELLOW key. 2 Auto Scan SCREEN 23 Press the GREEN key to set the scan mode to Free or Free+CA. When the set-up is completed, press the RED key to start the scan, shown as below. 3 Manual Scan In this menu, you can add a new transponder, edit the transponder or delete the transponder. SCREEN 25 Add Transponder: In this menu, you can add a new transponder to the system. Press the GREEN button, the Add Transponder sub-menu will appear on screen. Down Frequency: Symbol Rate: Polarity: SCREEN 26 Input the frequency of the new transponder. 27 UM 6005-15 ENG 1/26/06 4:18 PM Page 28 PART 1 English Edit Transponder: In this menu, you can edit a transponder in the system. Press the YELLOW button, the Edit Transponder sub-menu will appear on screen. Scan Press UP/DOWN to select a transponder, press the OK button to scan all the channels on the transponder. 28 UM 6005-15 ENG 1/26/06 4:18 PM Page 29 PART 1 English 5. 3 System setting In this menu, you can configure the systems such as language Setting, OSD style, Parental Control, TV Settings and Time Setting. Press OK/RIGHT to enter the language list and Press UP/DOWN to select the language. If you don't know which standard your TV has, please select AUTO. 3 Time Settings If a broadcaster provides GMT, you can set the time using GMT, or set your own time by yourself. If the GMT usage is ON then the Current time is set automatically or you can set the time zone. If your broadcaster provides the correct time offset then your receiver will change from summertime to wintertime automatically. [. . . ] It receives the signals reflected by the dish and converts them to signals that can be used by Satellite receiver. mPEG is a standard method for digital transmission of video and audio. A network which is also known as a bouquet is a set of channels that is offered by a single broadcaster. referring to the Phase Alternate Line colour system adopted by European broadcasters. [. . . ]