Detailed instructions for use are in the User's Guide.
[. . . ] Digital Free-To-Air Satellite Receiver SRT 6016
User Manual
Picture similar
Safety Instructions
SAFETY INSTRUCTIONS
Grounding, Polarization -- If this product is used with a specified AC adapter, the adaptermay be equipped with a polarized alternating current line plug (a plug with one blade wider than the other). This safety feature allows the plug to fit into the power outlet only one way. If you cannot insert the plug into the wall outlet, pull it out, reverse it, and then reinsert it. If the plug still fails to fit, contact an electrician and have the receptacle replaced n Protecting the Power Cord -- The power supply cord should be placed so it will not bewalked on. [. . . ] Press the OK button to add the selected channel to the Favourite group. To remove the channel from the favourite group, repeat same operation.
5. 2 Installation
The installation menu contains three sub-menus; "Antenna Installation", "Auto Scan" and "Manual Scan".
10
PART 1 · English
5. 2. 1 Antenna Installation
You can add a satellite, edit a satellite and delete a satellite in this menu. Add satellite If you want add a new satellite, press the RED key in this menu, a satellite list will appear on the screen. If the satellite does not exist in the satellite list, please select "NEW SAT1". After selection of a satellite from the satellite list, the Configure Antenna menu will appear, please set the LNB Type, LNB Low Freq, LNB High Freq, Band control, Polarisation control, DiSEqC Switch and Antenna mode. Edit satellite If the parameters of the satellite were changed or the satellite is a new satellite, you must set the parameters of the satellite, such as LNB type, LNB low Freq, LNB High Freq, Transponder, LNB Power, 22k Tone, DiSEqC and Antenna Mode. Sequence of editing of satellite parameters is same as sequence of "Add satellite" described in 4. 2 Delete satellite If you want to delete a satellite, press the YELLOW key. Select OK and press the OK key to confirm.
5. 2. 2 Auto Scan
Press the GREEN key to set the scan mode to Free or Free+Scrambled. If mode is Free then only "Free to Air" channels will be added to the channel list. If mode is Free+Scrambled then all channels from selected satellite will be added to the channel list. Blind scan function is useful to scan new added satellite, but scan may take long time. Press the BLUE Key to set the scan type to NIT OFF or NIT ON while Blind Scan is set to OFF and to Quick Search or Detail Search while Blind Scan is set to ON. When the set-up is completed, press the RED key to start the scan, shown as below.
5. 2. 3 Manual Scan
In this menu, you can scan single transponder, add a new transponder, edit the transponder or delete the transponder. You can switch between satellites with the RED button, Scan transponder: Use UP/DOWN buttons to select the transponder. Add Transponder: In this menu, you can add a new transponder to the system. 11
English
PART 1 · English
Edit Transponder: In this menu, you can edit a transponder in the system. Press LEFT/RIGHT to select OK, press the OK button to confirm.
5. 3 System setting
In this menu, you configure the system, such as Language Setting, OSD style, Parental Control, TV Settings and Time Setting.
5. 3. 1 Preference 5. 3. 1. 1 Language Setting
You can change the language of the OSD, preferred Audio and Subtitles. Use UP/DOWN to select the OSD language, Audio language or Subtitles language. Press OK or Right to enter the language list and Press UP/DOWN to select the language. Press OK to confirm.
5. 3. 1. 2 TV settings
You can set the TV mode, Screen mode and Video output. n TV mode In TV mode Screen press OK or RIGHT to select mode, press OK to confirm. If you don't know which standard your TV has, please select AUTO. [. . . ] 60 Mbits/s 720 x 576 (PAL), 720 x 480 (NTSC) pixels 4:3, 16:9
32, 44. 1, 48 kHz Stereo, Joint stereo, Dual mono, Mono
DVB-S 950 ~ 2150 MHz -25 ~ -65 dBm 13/18 V DC (+/- 5%) Max. 500 mA, Overload protected 1. 0 & 1. 2
16 Mbits 64 Mbits
PAL BG/I/DK /MN 21 ~ 69 selectable via OSD
Connectors: SAT IN, SAT OUT ANT IN, TO TV 2 SCARTS TV (RGB, CVBS) / VCR (CVBS) 3 RCA (Video, Audio Left & Right), S/PDIF: coaxial output Data Interface serial port: RS-232, 9-Pin D-Sub Male type Separate power switch
19
English
PART 1 · English
General Data: Input Voltage Range: Power consumption: Stand-by Power consumption: Operating Temperature: Storage Temperature: Operating Humidity Range: Size (WxDxH) in mm: Weight:
90 ~ 240 V AC 50/60 Hz max 20 W <9W +0 °C ~ 40 °C -30 °C ~ 80 °C 10 % ~ 85 %, RH, Non-condensing 260 x 210 x 40 1. 2 kg
A. 3 GLOSSARY OF TERMS
C band DiSEqC Fixed Dish Free-To-Air broadcast Ku band LNB 3. 7 ~ 4. 2 GHz Frequency. Unscrambled broadcast which you can view for free 11 ~ 13 GHz Frequency. It receives the signals reflected by the dish and converts them to signals that can be used by Satellite receiver. [. . . ]