User manual STRONG SRT 700 BROCHURE

[. . . ] Never put a heavy object on the power cord or wrap it around the leg of a table or chair. Keep the area around the power cord connection points, at the power outlet, and at the product connection, free of all AC adapter or accessory power cords n CAUTION: TO REDUCE THE RISK OF ELECTRICAL SHOCK, DO NOT REMOVE COVER (OR BACK). REFER TO QUALIFIED SERVICE FOR SERVICING. Explanation of WARNING symbols The lightning flash with arrowhead symbol within an equilateral triangle is intended to alert the user to the presence of not isolated dangerous voltage within the inside of the product that may be of sufficient magnitude to constitute a risk of electric shock to persons. The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and servicing instructions in the literature accompanying the appliance. [. . . ] In this menu, you can modify the Program Name, Down Frequency, Symbol rate, Video PID, Audio PID. If you want to rename the channel, use the UP/DOWN keys to select "Program Name" and press OK, the program name dialog will shown as below. Use the LEFT/RIGHT buttons to move the cursor to the character you wish to edit. If you wish to delete character you have to replace it with "space" character. Move channel Press the UP/DOWN keys to point the focus of the menu to the channel of your selection. Press the LEFT/RIGHT keys to point the focus of the menu to the column "Move". When the focus is on column "Move", press the OK button to confirm selection of the channel, using the UP/DOWN buttons move the channel to its new location and press the OK button to confirm the new location. Delete channel Press the UP/DOWN keys to point the focus of the menu to the channel of your selection. Press the LEFT/RIGHT keys to point the focus of the menu to the column "Del". When the focus is on column "Del", press the OK button to mark the channel as selected to be deleted from the list. To apply the changes press the EXIT button and confirm the channel's deletion. n TV mode In TV mode Screen press OK or RIGHT to select mode, press OK to confirm. If you don't know which standard your TV has, please select AUTO. n Screen mode In TV format Screen press OK or RIGHT to select 4:3 or 16:9, press OK to confirm. n Video output In Video output Screen press OK or RIGHT to select CVBS or RGB, press OK to confirm. n Modulator settings Use UP/DOWN to select RF Audio mode or RF channel. Use LEFT/RIGHT to change the settings and press OK to confirm the settings or EXIT to cancel. 5. 3. 1. 3 Time Settings If a broadcaster provides GMT, you can set the time using GMT, or set your own time by yourself. If you set GMT Usage to OFF, Set Data and Set Time item are displayed. To set the time value manually, move the cursor to the time item and use the numeric buttons on the remote control. 5. 3. 1. 4 Set Factory Default Please be careful when using this function, because it will erase all the data and parameters you may have set earlier to your receiver. Once you set the factory default you will have to re-install your preferences and re-scan your channels. To reset your receiver to factory default, apply the following steps: 12 PART 1 · English Select Set Factory default and press OK. Confirm warning message with OK and press the OK key, the receiver will return to its factory default state, and all user data will be deleted. [. . . ] Set the values of the tuner parameters correctly in the installation menu. Check the signal strength with a spectrum analyzer and adjust your dish correctly. Check whether the batteries are inserted correctly in your remote control. Check the batteries, and if exhausted replace the batteries in the remote control. Incorrect values of some tuner parameters Wrong direction of the dish Message "Antenna Power Overload" displayed on TV Receiver detected short cut in your cable system The remote control does not work The batteries of the remote controller are not inserted or exhausted 18 PART 1 · English A. 2 SPECIFICATIONS Demodulator Modulation: QPSK Input Symbol Rate: 2 ~ 45 Ms/s SCPC & MCPC signals from C & KU and satellites Video Decoder Profile level: Input Rate: Video Resolution: Aspect Ratio: Audio Decoder: ISO/IEC 11172 LAYER I&II Sampling rate: Audio modes: Tuner Front-End: Input Frequency Range: RF Input Level: LNB Power: DiSEqC Version: System and Memory: Flash Memory: SDRAM: UHF Modulator Standards: Channel: MPEG-2 MP@ML Max. [. . . ]