User manual STRONG SRT 5245

[. . . ] Digital Satellite and Terrestrial Receiver SRT 5245 User Manual Immagine simile ENVIRONMENTAL ISSUES Strong is committed to reducing the impact of its products on the environment. Electronic product recycling Do not dispose of this product with your domestic rubbish. Packaging When disposing of this product packaging, please ensure that it is recycled. At the end of its useful life, this product contains materials which when processed correctly can be recovered and recycled. By participating in the responsible recycling of this product you will be reducing the requirement for new raw materials and reducing the amount of material that would otherwise end up in landfill. When you purchase a new, similar product your retailer may offer to take this old one off you. Your retailer or local municipal authority will advise you of the collection facilities available for waste electronically products in your area. [. . . ] Be aware: after pressing BLUE button channel(s) will be deleted from all channel lists. Press EXIT to cancel data save or OK to confirm data save. 5. 2 Satellite set-up The Satellite set-up menu contains following sub-menus: "Channel set-up" allow you to setup channels from selected satellites. "Dish Set-up" allow you to setup configuration of your dishes. "Edit satellites" allow you to edit predefined satellites and their transponders as well as add new satellites. "GOTO X setup" allow you to setup your location in order to use GOTO X type of positioner. 12 PART 1 · English 5. 2. 1 Channel set-up From this menu you can setup channels from satellite(s) in several modes, access to Dish setup menu, Positioner setup (if used). If satellite doesn't exist in the list you should add it first using "Edit satellites" menu. Use buttons to select dish number to which above selected satellite belongs to. Dish number "--" means that selected satellite do not belongs to any dish. n if mode of selected dish is "Fixed" then this item is not selectable. n if mode of selected dish is "DiSEqC 1. 2" then value can be "Not stored" (in case dish position for selected satellite was not stored) or in range from 1 to 64 if position has been stored. n if mode of selected dish is "GOTO X" then value is "GOTO X". List of transponders of selected satellite will appear at right side of the screen. You can select transponder in order to check signal strength and quality of reception. If you need to modify transponder list please use menu "Edit satellites" as described in chapter 5. 2. 3. If you need to scan specific transponder then use Manual scan as described in this chapter below. Network search: if this item is set to "OFF" then receiver will search for the channels that are available from preset transponder list of selected satellite. If this item is set to "ON" then receiver in addition will search for the channels from transponders information about that can be found from broadcast. Search for: you can select type of the channels that will be installed to your receiver. n If selected "All channels" then receiver will install Free-To-Air and Scrambled channels n If selected "Scrambled" then receiver will install only Scrambled channels n If selected "FTA" then receiver will install only Free-To-Air channels Once you complete all settings you can start channel search process. Press RED button to setup channels from all transponders of the satellite; Press GREEN button to setup channels from transponder selected in Transponder item; Press YELLOW button to enter to Manual setup channels from specific transponder or to setup single channel with known Video and Audio PID. 13 English PART 1 · English Manual setup of channels In Manual channel search menu you can setup all channels from specific transponder or single channel. To setup all channels from specific transponder: Satellite: Indicate name of the satellite where channels will be searched Frequency: Use Numeric buttons to enter frequency of transponder Polarisation control: Use tupq buttons to select polarisation of transponder Symbol rate: Use Numeric buttons to enter symbol rate value Network search: Use tupq buttons to select ON or OFF Search for: Use tupq buttons to select type of channels to be installed Press RED (Search) button to start channel search. 5. 2. 1. 1 Positioner setup If in Dish setup menu you have configured Dish mode as "DiSEqC 1. 2" then you have to setup position of the dish to each satellite that you want to install. [. . . ] Use tupq buttons to select channel and press OK to switch to full screen view mode. Use button LIST to change a list between "ALL channels" and one satellite or only terrestrial channels mode. 6. 3. 1 Fast alphabet filtering Press RED (Filter) button to filter channels in alphabet order. Select first letter of the channel name that you need to find in the list and press OK. [. . . ]